Subscribe to Our Youtube Channel
Related Manuals for MEE AUDIO M6 VR
Summary of Contents for MEE AUDIO M6 VR
- Page 1 M U LT I P L AT F O R M I N - E A R G A M I N G H E A D P H O N E S M6 VR SETUP GUIDE Scan QR code or visit: MEEaudio.com/M6VRVid...
- Page 2 M6 VR PACKAGE CONTENTS PACKAGE CONTENTS Earpieces Protective Carrying Case Silicone Cable Bracket with Velcro Strap Velcro Cable Organizers Silicone Eartips (6 pairs) Short Cable for VR headsets Extension Cable for VR headsets Headset Cable for consoles and other devices...
- Page 3 EARTIP SELECTION INSTALLING EARTIPS Multiple sets of eartips are included to ensure you get the best fit with your headphones. The correct eartips for your ear will allow the earpieces to fit flush, reduce outside noise, and provide good bass response. Install eartips as shown.
- Page 4 INSTALLATION FOR VR HEADSET INSTALLATION FOR VR HEADSET: OVERVIEW The M6 VR can be used with the Oculus Quest and select other VR headsets. Follow the instructions in steps 1-5 to install and wear your M6 VR with optimal comfort and freedom of movement.
-
Page 5: Installation - Step
INSTALLATION - STEP 1 STEP 1: INSTALLING THE EXTENSION CABLE Plug the Extension Cable (G) into the 3.5 mm jack of your VR headset. - Page 6 INSTALLATION - STEP 2 STEP 2: SECURING THE EXTENSION CABLE Route the Extension Cable (G) over the front of the headset and through the top strap. Secure the Extension Cable (G) at the base of the top-strap using a Velcro Cable Organizer (D)*. *Tip: secure the tail end of the Velcro Cable Organizer (D) around the cable first.
- Page 7 INSTALLATION - STEP 3 STEP 3: MOUNTING THE CABLE BRACKET Insert the jack of the Extension Cable (G) into the Silicone Cable Bracket (C) and secure the Silicone Cable Bracket (C) to the top strap of the VR headset using the Velcro Strap. Mount the Silicone Cable Bracket (C) as far back as possible on the strap to eliminate cable slack.
- Page 8 INSTALLATION - STEP 4 left right cable cinch STEP 4: WEARING THE M6 VR IN-EARS Until you become familiar with the over-the-ear fit Bend the memory wire around each ear and slide of the earpieces, we recommend putting them on the cable cinch up to tighten for the most secure fit.
- Page 9 INSTALLATION - STEP 5 STEP 5: CONNECTING THE SHORT CABLE TO THE INSTALLED EXTENSION CABLE Once the earpieces are in your ears, put on your VR headset and plug the Short Cable (F) into the previously installed Extension Cable (G). You’re all set!
- Page 10 USE WITH OTHER DEVICES The included Headset Cable (H) can be used with PCs, laptops, gaming consoles/controllers, tablets, smartphones, and other devices with a standard 3.5 mm headset jack. REPLACING THE CABLE To detach the cable, grasp the earpiece and cable connector firmly, and pull straight apart without twisting.
- Page 11 USE WITH OTHER DEVICES (CONT.) CONNECTOR GROOVES CONNECTOR NOTCH REPLACING THE CABLE (CONTINUED) Attach the new cable by lining up the notches on the connectors with the grooves in the earpieces as shown. Push the connectors in until they fit securely. Make sure to attach the cable connector marked “R”...
- Page 12 USE WITH OTHER DEVICES (CONT.) left right HOW TO WEAR THE HEADSET CABLE Identify the right and left earpieces. Straighten the memory wire and put each earpiece in the corresponding ear. Adjust each earpiece until it fits flush in your ear and the eartip seals the ear canal.
- Page 13 USE WITH OTHER DEVICES (CONT.) Holding the earpiece in place, bend the memory wire around your ear to achieve a conforming fit. While pulling the cable gently with one hand, squeeze the memory wire behind your ear with the other hand until the fit is tight and secure.
- Page 14 USE WITH OTHER DEVICES (CONT.) Slide the cable cinch up to tighten for the most secured fit. Use the shirt clip to control cable movement.
- Page 15 MICROPHONE & REMOTE USE The Headset Cable (H) features an inline microphone and remote. Basic remote operation with mobile devices: Function Operation Answer / End Press the phone call remote button Play / Pause Press the media* remote button Skip to next track** Double-press the remote button Restart the track /...
- Page 16 PERSONALIZATION Custom-Engraved Faceplates The M6 VR can be personalized with engraved metal faceplates. Choose from our existing artwork options or submit your own custom design. Visit the URL below to learn more and order faceplates. Use a PC or Mac for best results: www.MEEaudio.com/Faceplates...
-
Page 17: Additional Support
Contact local authorities to learn about disposal and recycling options. MEE audio and its logo are registered trademarks of S2E, Inc. All rights reserved. Microsoft and Xbox are trademarks of the Microsoft group of companies. -
Page 18: We're Here To Help
IMPORTANT Please read this quickstart guide in its entirety to ensure best fit and sound QUESTIONS? WE’RE HERE TO HELP! Phone Support: 626-965-1008 Monday ~ Friday 9:00 am to 5:00 pm PST Email Support: support@MEEaudio.com All emails are responded to within 2 business days...
Need help?
Do you have a question about the M6 VR and is the answer not in the manual?
Questions and answers