Advertisement
DO NOT operate the cleaning tank if any parts are missing or damaged as this may cause failure or possible personal injury.
DO NOT modify or jam the cleaning tank lid open. Retain the lid open by use of the attached elbow strut only.
7
DO NOT use any solvent with a flash point below 105
7
DO NOT over fill the cleaning tank with solvent.
7
DO NOT leave the cleaning tank operating unattended.
7
DO NOT operate the cleaning tank when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
The tank is not suitable for paint thinners, gun wash or air drying.
7
When not in use switch the cleaning tank off, remove plug from the power supply.
7
Dispose of waste liquids in accordance with local authority regulations.
3
p WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
3
2. APPLICATION & SPECIFICATIONS
One piece tank with a triple baked finish and fully sealed magnetic drive pump unit with replaceable impeller. This small capacity tank is suitable
for bench-top mounting. Recirculated fluid is filtered before entering the pump and is directed over the work piece with a flexible metal delivery nozzle.
The lid is fitted with fusible link device.
SPECIFICATIONS
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Motor power . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20W
Tank Height/width/length (mm) . . . . . . . . .220/330/430
3. OPERATING INSTRUCTIONS
WARNING! Ensure you have read, understand and apply chapter 1 safety instructions before using the cleaner.
3.1.
Check that the washer power switch is in the off position, and that the unit is unplugged from the mains power supply.
p
3.2.
Fill the tank to appropriate capacity (Min. 7ltrs Max. 13ltrs) with Sealey solvent, or a general purpose degreaser (contact your local
dealer for supply). DO NOT use any other type of solvent. CAUTION! Ensure you follow any instructions provided with the solvent.
3.3.
Ensure the pump is immersed correctly in the solvent.
3.4.
Plug the washer into the mains power supply and switch the unit on. Check that solvent flows freely through the flexible spigot.
3.5
Place parts to be cleaned onto the cleaning tray. Direct spray nozzle onto parts. Ensure any splash back stays inside the tank, if not
reposition the spray nozzle. For ground-in marks, leave the parts to soak in the bottom of the tank. Brush parts with cleaning brush if
required. Turn off the pump and leave the parts to drain either in the basket, or if too large, on the shelf.
3.6.
When complete turn the washer off and unplug from the mains power supply.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment. Dispose of waste liquids according to local
authority regulations.
p
3.7.
Keep the cleaning tank clean. Remove and clean the filter regularly for best and safest performance.
IMPORTANT! The SM21/C has an anti-fire device built into the unit. In the event of a fire the lid will automatically close. DO NOT prop the lid
open as this will prevent the automatic safety feature from operating. Once actuated, the fire detection device cannot be re-used and must
be replaced before further use.
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following
standards and directives.
WORKSHOP CLEANING TANK MODEL SM21/C
93/68/EEC CE Marking Directive
89/336/EEC EMC Directive
73/23/EEC Low Voltage Directive
98/37/EC Machinery Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this equipment
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
F. Use only Sealey solvent, contact your local dealer for details.
O
Overall height . . . . . . . . . . . . . . . . . . . . . . . . . .250mm
Minimum working capacity . . . . . . . . . . . . . . . . . 7Ltrs
Overall maximum tank capacity . . . . . . . . . . . . . 27Ltrs
Pump output/hr . . . . . . . . . . . . . . . . . . . . . . . .360Ltrs
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.5kg
The construction file for this product is held by the Manufacturer
and may be inspected on request by contacting Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 703534
9th March 2000
E-mail: sales@sealey.co.uk
SM21/C - 0016 - (2) -090300
Advertisement
