Subscribe to Our Youtube Channel
Summary of Contents for Ecler VEO-XWT44E
- Page 1 VEO-XWT44E HDBASET EXTENDER HDbaseT Wallplate Transmitter, EU format USER MANUAL v.20201217...
-
Page 2: Table Of Contents
INDEX IMPORTANT REMARK ......................3 IMPORTANT SAFETY INSTRUCTIONS ................3 IMPORTANT NOTE ........................ 5 INTRODUCTION ........................5 PACKAGES CONTENT ......................6 PANEL DESCRIPTIONS ......................7 6.1. Front Panel ........................... 7 6.2. Rear Panel ............................ 8 SYSTEM CONNECTION ......................9 BUTTON CONTROL ......................10 8.1 Source Switching ........................ -
Page 3: Important Remark
IMPORTANT REMARK The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. - Page 4 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.
-
Page 5: Important Note
Ecler VEO-XWT44E comes with a 3-year warranty. INTRODUCTION Ecler VEO-XWT44 is a HDbaseT transmitter in European 2-gang wallplate format. It allows to extend one 4K video signal up to 40m over a single Cat 5e/6 cable or a FullHD signal up to 70m when connected to VEO-XRT44. It supports real 4K video signals at 60Hz with 4:4:4 YUV chroma subsampling and HDR 10 with a maximum bandwidth of 18Gbps. -
Page 6: Packages Content
Firmware upgrade by Micro-USB port. ⚫ ESD protection ⚫ PACKAGES CONTENT 1 x VEO-XWT44E Transmitter / Switcher 1 x Surface mount box EU 2 x Mounting screws 1 x 3-pin Euroblock 3 x 2-pin Euroblock 1 x Power Adapter (24V DC 1.25A) with international blades... -
Page 7: Panel Descriptions
PANEL DESCRIPTIONS 6.1. Front Panel 1. LINK LED: The LED illuminates green when the transmitter is successfully connected to the receiver by a CATx cable. 2. HDCP LED: a. The LED illuminates green when the HDMI signal is transmitted with HDCP. -
Page 8: Rear Panel
12. USB-C LED: The LED illuminates orange when the USB-C port is connected to a source device, and it will turn green once the device is selected as input source. 13. DISPLAY ON/OFF: Press the blue-backlight button to turn on/off the display by automatically sending CEC and RS-232 command (Programming required). -
Page 9: System Connection
SYSTEM CONNECTION The following diagram illustrates typical input and output connection that can be utilized with the switcher: Note: We recommend the use of CATx shielded cables in order to guarantee the performances declared in the HDbaseT protocol specs. -
Page 10: Button Control
BUTTON CONTROL 8.1 Source Switching 1) Press the SOURCE AUTO button to switch to next source device, and then the corresponding input LED will turn green. 2) Press and hold the SOURCE AUTO button at least 3 seconds to enable auto switching mode. -
Page 11: Rs-232 Control
RS-232 Control 9.1. RS-232 Connection According the RS-232 control mode, there are three types of RS-232 connection for different application. 1. To control the switcher from local, please connect a control device (e.g. PC) to the RS-232 port of the switcher. 2. -
Page 12: Rs-232 Commands
RS-232 COMMANDS The following table lists all the commands available for the VEO-XWT44E. Note: • Command ending: “<CR><LF>”. • Feedback Error: “COMMAND ERROR” or “OUT OF RANGE”. • In the table, “[”and “]” are symbols for easy reading and do not need to be typed in the command. -
Page 13: Source Switching
10.2. Source Switching Command Description Feedback Example #SET_AV H1 Switch to HDMI 1. @AV H1 #SET_AV H2 Switch to HDMI 2. @AV H2 #SET_AV C Switch to USB-C. @AV C @AV H1 #GET_AV Get the current input source. @AV H2 @AV C #SET_AUTO_SWITCH 1 Enable auto switching mode. -
Page 14: Edid Management
10.4. EDID Management The Extended Display Identification Data (EDID) is used by the source device to match its video resolution with the connected display. By default, the source device obtains its EDID from the connected display, but when the video resolution of display is higher than 4K@30Hz, the video resolution of source device will be 4K@30Hz. -
Page 15: Display Control
Command Description Feedback Example @EDID_MODE 7 @EDID_MODE 8 @EDID_MODE 9 10.5. Display Control Command Description Feedback Example #SET_DISPLAY ON Power on the display device (CEC/RS232/IR). @SET_DISPLAY ON #SET_DISPLAY OFF Power off the display device (CEC/RS232/IR). @SET_DISPLAY OFF #SET_VOL + Volume up the display device. @VOL + #SET_VOL - Volume down the display device. -
Page 16: Third-Party Device Control
10.6. Third-party Device Control Command Description Feedback Example Send the ASCII command "xxxx" to the third- #SEND_A_01:ABCD123 party device which is connected to the HDBaseT receiver. The baud rate of the third- party device is [PARAM]. [PARAM] = “01~07”. Represents the baud #SEND_A_[PARAM]: rate of the third-party device. -
Page 17: User Defined Button
USER DEFINED BUTTON Pressing the DISPLAY ON/OFF button allows turning the display on and off via CEC commands. If the display doesn’t support CEC, the DISPLAY ON/OFF button can be programmed by IR learning feature or RS-232 command. 11.1. IR learning programming Please follow the IR learning steps below in order to define the DISPLAY ON/OFF button functions: 1. -
Page 18: Rs-232 Programming
11.2 RS-232 programming The DISPLAY ON/OFF button also can be programmed to send RS-232 commands by the following instructions: Command Description Feedback Example Enable sending RS232 command when the DISPLAY #SET_KEY_RS232 ON @KEY_RS232_SENDING ON ON/OFF button has been pressed. Disable sending RS232 command when the DISPLAY @KEY_RS232_SENDING #SET_KEY_RS232 OFF ON/OFF button has been pressed. - Page 19 Command Description Feedback Example Set the RS232 command "xxxx" to be sent to the third- party device when the DISPLAY OFF button has been pressed. [PARAM1] = A/H: ⚫ [PARAM1] String ASCII [PARAM2] = “01~07”: Represents the baud rate of ⚫...
-
Page 20: Technical Specifications
TECHNICAL SPECIFICATIONS Video performances Supported Resolutions Up to 4Kx2K@60Hz 4:4:4 8bit HDR10 Colorspace RGB, YCbCr Chroma Subsampling 4:4:4, 4:2:0 Color depth 8-bit, 10-bit, 12-bit, 16-bit only @4K30 Signal Bandwidth 18 Gbps HDCP 2.2/1.4 Compliant Video Connectors 2xType-A Female HDMI, Type-C Female USB Audio performances Audio Formats PCM 2Ch, PCM 5.1, PCM 7.1, Dolby Digital, DTS,... - Page 21 RS-232 MUTE RS-232 General HDMI Distance up to 10 meters / 33 ft with Ecler VEO cables Transmission Standard HDbaseT Cat.5e/6 Distance CAT5e/6 @ 4K up to 35 m / up to 115 feet CAT6a/7 @ 4K up to 40 m/ up to 130 feet...
-
Page 22: Mechanical Diagram
MECHANICAL DIAGRAM... - Page 23 NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications. For technical queries contact your supplier, distributor or complete the contact form on our website, Support / Technical requests. Motors, 166‐168 08038 Barcelona ‐ Spain ‐ (+34) 932238403 | information@ecler.com www.ecler.com...
Need help?
Do you have a question about the VEO-XWT44E and is the answer not in the manual?
Questions and answers