USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Specifications: Max Drilling Diameter 25mm(1”) Motor Power 750W Chuck Capacity 5-20mm Input Voltage - Frequency 230V - 50Hz Spindle Travel 85mm Number of Speeds Speed 50Hz 280-2830R.P.M. Spindle Taper Max.
Page 4
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Safety Information: (continued) Equipment Safety • Always keep guards in place and in clean, working order. A guard or other part that is damaged should be properly repaired or replaced using Jefferson approved parts.
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Assembly Instructions Base & Column Fig.1 Fig.2 1. Carefully remove contents from the packing box. 2. Select a firm, level surface on which to assemble the bench drill.
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Settings & Adjustments Fig.22 Fig.23 Table Height Adjustment 1. Loosen the table support lock (Fig. 22). 2. Rotate the table adjustment handle to set the desired table height and tighten the table rock to secure the table in position (Fig.
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Pre-Setting The Drilling Depth Fig.32.1 Fig.32.2 To set the depth of the hole, adjust the depth stop as follows: • Loosen depth stop lock knob by turning in an anti-clockwise direction see (Fig.32.1)
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Drilling 1. Ensure the bench drill is switched off and disconnected from the power supply. 2. Loosen the jaws of the chuck with the chuck key by turning in an anti-clockwise direction and insert the selected drill bit into the as far as it will go.
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Noisy operation a. Incorrect belt tension a. Adjust tension (under load) b. Dry spindle b. Remove spindle and quill assembly and lubricate c. Loose pulley c.
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Environmental Protection Recycle any packaging and unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
2011/65/EU (as amended) RoHS Directive Equipment Category: Bench Drill / Pillar Drill / Drill Press EU Member State United Kingdom Product Name/Model: JEFPDB0750-12S - 750W Pilllar Drill Signed by: Stephen McIntyre Position in the company: Operations Director Date: 19 August 2019...
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Limited Warranty Statement Jefferson Professional Tools & Equipment, or hereafter "Jefferson" warrants its customers that its products will be free of defects in workmanship or material. Jefferson shall, upon suitable notification, correct any defects, by repair or replacement, of any parts or components of this product that are determined by Jefferson to be faulty or defective.
Page 19
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz Claiming Warranty Coverage The end user must contact Jefferson Professional Tools & Equipment (Tel: +44 (0) 1244 646 048) or their nearest authorised Jefferson dealer where final determination of the warranty coverage can be ascertained.
Page 20
USER MANUAL v1.2 JEFPDB0750-12S 750W Pillar Drill • 12-Speed • 230V ~50Hz IMPORTANT! SAFETY FIRST! Before attempting to use this product please read all the safety precautions and operating instructions outlined in this manual to reduce the risk of fire, electric shock or personal injury.