Download Print this page

Abode Cyclo AB4176 Manual

Wall mounted bath shower mixer

Advertisement

Quick Links

Important Technical Data
Minimum operating pressure 1.5 bar* (Bath), 1.5 bar* (Shower)
Maximum operating pressure 5.0 bar*
Maximum hot water temperature 70°C*
Recommended hot water temperature 46°C
Note: If these temperatures or pressures are exceeded, even for
short periods, damage can result. In these instances a
thermostatic mixing or pressure reducing valve should be
installed.
For manual mixing products we recommend the installation of a
separate TMV2 product to reduce the risk of accidental scalding.
All thermostatic products should be tested and cleaned at least
once a year.
Hot and cold supply pressures should be as closely balanced as
possible for best results. Supply pipes should maintain the
maximum diameter until immediately before the fitting. The
differential between the hot and cold water supply temperatures
should be sufficient to allow correct mixing function.
Manufacturers Product Reference
AB4176
AB4198
©Abode
09/2017
Unit L, Zenith Park, Whaley Road, Barnsley, S75 1HT.
Tel: 01226 283434 Fax: 01226 282434 www.abodedesigns.co.uk
All errors and omissions excepted.
All Abode taps are either WRAS approved or
manufactured in accordance with recognised European
standards. Please ensure that your Abode product is
fitted in accordance with Local Water Byelaws.
Where hot and cold water mix within any product, then
suitable non return valves should be installed to the hot
and cold supplies to prevent backflow.
Whilst assembling this product take care not to
accidentally loosen any screwed assemblies. PTFE tape
can be used to ensure watertight joins on threaded
connections, do not over tighten connections or allow
pipes to be twisted or folded.
The installation should be periodically checked for
damage, if the property is left unattended for a prolonged
period we recommend isolating water supplies.
All errors and omissions excepted.
Cyclo Wall Mounted Bath Shower Mixer
5 Year warranty
Terms and Conditions
In the unlikely event that you should experience any
defect in the materials or workmanship of your new
Abode tap within FIVE years of purchase, the
purchaser's sole remedy shall be the replacement
(at the manufacturer's discretion) of all or any part of
the product that is defective. All working parts and
valves are guaranteed for a period of FIVE years
from purchase. Decorative surface finishes and O-
rings are guaranteed for ONE year from the date of
purchase provided that our advice concerning care
has been observed and no scouring agents have
been used.
This is provided that the tap has been used for
normal domestic purposes in the UK and that the
care, installation and maintenance instructions have
been observed. The warranty extends to the original
purchaser only. You should retain a copy of your
dated invoice as proof of purchase to validate any
claims under this guarantee.
Marks, scuffs and scratches caused by improper
installation or accidental damage are not covered by
this guarantee. Neither are shade variations or any
Care Instructions for your Bath Mixer
To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A
solution of warm water and a mild liquid detergent may be used where necessary, and then the fitting rinsed
thoroughly and wiped dry. Any other cleaning action or cleaning products will invalidate your warranty.
If the product has a removable spout diffuser it can be unscrewed and cleaned periodically in warm water to maintain
flow.
Abrasive cleaners, scouring cleaners, limescale cleaners and acidic cleaners must not be used under any
circumstances. Avoid contact with all solvents (including chlorinated solvents, ketones or acetones as these may
result in surface deterioration or etching). Also avoid contact with any harsh household chemicals such as bleach
cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, toothpaste, mouthwash, bar keepers
friend or Brasso.
Please leave these instructions for your customer.
damage or defect caused by incorrect installation or
abuse of the fitting.
As we are continuously improving and developing
our range of products, finishes & colours, in the
event of a valid claim, we may not be able to provide
an identical replacement for the defective product
throughout the guarantee period. Where an identical
product is no longer available, we will supply the
nearest equivalent from our then current product
range. In assessing your claim, we must be given
the opportunity to inspect the product as installed
prior to removal. Any product returns must be
packaged as received and complete.
No other warranties, express or implied, are made,
including merchantability or fitness for a particular
purpose. Under no circumstances shall the
manufacturer be liable for any loss or damage
arising from the purchase, use or inability to use this
product, or for any special, indirect, incidental or
consequential damages. No liability is accepted for
consequential damage to other household fixtures,
fittings or furnishings arising from this claim, even if
attached to the product. No installer, dealer, agent or
employee of Abode has the authority to modify the
obligations or limitations of this warranty.

Advertisement

loading

Summary of Contents for Abode Cyclo AB4176

  • Page 1 No installer, dealer, agent or employee of Abode has the authority to modify the Marks, scuffs and scratches caused by improper obligations or limitations of this warranty.
  • Page 2 Preparation Service Instructions All parts should be removed from their packaging and inspected for any transport damage and completeness prior to Replacing the valve cartridge installation; you should read these instructions throughout before commencing installation. We do not accept responsibility for problems that may occur through improper installation. Always ensure you have sufficient hot and cold water pressure available to allow correct function before specifying or installing this product.
  • Page 3 After installation Once you have visually checked the installation of the new tap and all connections, ensure that all other fittings are closed except the tap which should be left open. Turn on your water heating system and ensure that your mains stopcock is open. Reconnect both the hot and cold water supplies to this fitting.
  • Page 4 Parts and Contents Installation Instructions: Connect spout connector (F) to back body as shown using 2 x bolts supplied using a 3mm allen key. Connect hand shower holder connector (I) to back body as shown using 2 x bolts supplied using a 3mm allen key.

This manual is also suitable for:

Cyclo ab4198