Related Manuals for EINHELL TP-AG 1212 E
Summary of Contents for EINHELL TP-AG 1212 E
- Page 1 TP-AG 1212 E Originalbetriebsanleitung Winkelschleifer Art.-Nr.: 44.309.12 I.-Nr.: 11013 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 1 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 1 02.07.13 15:18 02.07.13 15:18...
- Page 2 - 2 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 2 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 2 02.07.13 15:18 02.07.13 15:18...
- Page 3 - 3 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 3 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 3 02.07.13 15:19 02.07.13 15:19...
- Page 4 30°-40° - 4 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 4 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 4 02.07.13 15:19 02.07.13 15:19...
- Page 5 Caution - Read the operating instructions to reduce the risk of inquiry Wear ear-muff s. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.
-
Page 6: Safety Information
• Additional anti-vibration handle Important! • Guard When using equipment, a few safety precautions • Original operating instructions must be observed to avoid injuries and damage. • Safety instructions Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times. -
Page 7: Before Starting The Equipment
5. Before starting the equipment Surface sanding/grinding Vibration emission value a = 4.2 m/s K uncertainty = 1.5 m/s Before you connect the equipment to the mains supply make sure that the data on the rating plate Warning! are identical to the mains data. The specifi... -
Page 8: Operation
5.4 Test run for new grinding Wheels 6.3 Changing the guard (Fig. 3) • Allow the right-angle grinder to run in idle for at Remove the two flanges. • least 1 minute with the grinding or cutting wheel Press the clamping lever (a) and turn the gu- fi... -
Page 9: Replacing The Power Cable
7. Replacing the power cable 6.6 Motor It is vital for the motor to be well ventilated during operation. Be sure, therefore, to keep the ventilati- If the power cable for this equipment is damaged, on holes clean at all times. it must be replaced by the manufacturer or its after-sales service or similarly trained personnel 6.7 Grinding Wheels... -
Page 10: Disposal And Recycling
9. Disposal and recycling The equipment is supplied in packaging to pre- vent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. - Page 11 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH. Subject to technical changes - 11 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 11 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 11 02.07.13 15:19 02.07.13 15:19...
- Page 12 Arabic - 12 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 12 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 12 02.07.13 15:19 02.07.13 15:19...
- Page 13 Arabic " - 13 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 13 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 13 02.07.13 15:19 02.07.13 15:19...
- Page 14 Arabic - 14 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 14 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 14 02.07.13 15:19 02.07.13 15:19...
- Page 15 Arabic - 15 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 15 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 15 02.07.13 15:19 02.07.13 15:19...
- Page 16 - 16 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 16 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 16 02.07.13 15:19 02.07.13 15:19...
- Page 17 - 17 - Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 17 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 17 02.07.13 15:19 02.07.13 15:19...
- Page 18 EH 06/2013 (01) Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 18 Anl_TP_AG_1212_E_SPK7_EX_KSA.indb 18 02.07.13 15:19 02.07.13 15:19...