Subscribe to Our Youtube Channel
Related Manuals for BDI SEQUEL 20 6102
Summary of Contents for BDI SEQUEL 20 6102
- Page 1 SEQUEL 20 6102 ® CONSOLE INSTRUCTION MANUAL LET’S GET STARTED. DESIGN MATTHEW WEATHERLY...
- Page 3 Congratulations on the purchase of your Sequel 20 Console 6102 from BDI. Your console has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information that will ensure that you get the most out of your console.
- Page 4 HARDWARE AND COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product.
- Page 5 HARDWARE AND COMPONENTS PART # PART # DESCRIPTION DESCRIPTION Upper Horizontal Frame 6108 Back Panel—SOLD SEPARATELY QUANTITY QUANTITY PART # PART # DESCRIPTION Top Panel DESCRIPTION Front Panel QUANTITY QUANTITY NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.COM | 5...
- Page 6 (C1) Left and (C2) Right Leg Frames. (H1) Screw heads should be 1/4" (6mm) H1-SCREW away from frame. Screw Heads 1/4" (6mm) away from frame 6 | BDIUSA.COM SEQUEL 20 6102...
- Page 7 STEP 3. INSTALL TOP FRAME ASSEMBLY On a soft surface such as a carpet, position (C2) Right Leg Frame as shown and hook (C3) Top Frame onto the partially threaded screws on the top of (C2) Right Leg Frame. Slide the frame down so that the screws go into the keyhole slot.
- Page 8 Lift and hook the (C3) Top Frame onto the 2 PART/DESCRIPTION partially threaded screws at the top of (C1) Left Leg Frame. Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex T1-HEX WRENCH Wrench. H1-SCREW 8 | BDIUSA.COM SEQUEL 20 6102...
- Page 9 STEP 5. INSTALL LOWER HORIZONTAL FRAME ASSEMBLY Lift and hook the (C4) Lower Horizontal Frame PART/DESCRIPTION onto the partially threaded screws as shown. Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench. T1-HEX WRENCH H1-SCREW C1/C2 C1/C2 NEED ASSISTANCE? customerservice@bdiusa.com...
- Page 10 Lift and hook the (C5) Upper Horizontal Frame PART/DESCRIPTION onto the partially threaded screws as shown. Insert (H1) Screws into the lower holes and fully tighten with (T1) Hex Wrench. T1-HEX WRENCH Including previous steps, fully tighten all screws! H1-SCREW C1/C2 10 | BDIUSA.COM SEQUEL 20 6102...
- Page 11 STEP 7. INSTALL TOP PANEL ASSEMBLY Install the (C8) Top Panel as shown and secure PART/DESCRIPTION with (H1) Screws going though the metal tabs on the frame and into the inserts in the corners of the guide blocks under the (C8) Top Panel. T1-HEX WRENCH Tighten using the (T1) Hex Wrench.
-
Page 12: Step 9. Install Front Panel
Install the (C9) Front Panel by placing the bottom edge into the channel on the front of the (C4) Lower Horizontal Frame. Rotate back and vertically until the top edge magnetically attaches to the frame. 12 | BDIUSA.COM SEQUEL 20 6102... -
Page 13: Fine Tuning
FINE TUNING LEVEL DESK If needed, dial out 1 or more of the levelers using (T2) Leveler Wrench. WIRE MANAGEMENT FINE TUNING Wires and cords may be routed as shown through the space. NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.COM | 13... -
Page 14: Care And Maintenance
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid positioning your BDI cabinet in any area with extensive direct sunlight. -
Page 15: Warranty
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. - Page 16 These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.08.21.2020 Made in Vietnam.
Need help?
Do you have a question about the SEQUEL 20 6102 and is the answer not in the manual?
Questions and answers