Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for True FS-65
- Page 1 FS-65 HOULDER RESS SSEMBLY ANUAL Model: FS65 Rev: 030620...
- Page 2 TRUE experience. Innovation across the full product line has made TRUE successful and is a trademark of the TRUE heritage. TRUE’s patented Heart Rate Control technology is just one of the remarkable ways we deliver simple and superior performance every user can enjoy, and most importantly, use to achieve personal health and fitness goals.
-
Page 3: Table Of Contents
ABLE ONTENTS ........................4 AFETY ................ENERAL ARE AND AINTENANCE ................... 8 IMENSIONS AND EIGHT ......................9 REPARATION .................... 10 ARTON ONTENTS .................... 11 ARTON ONTENTS & A NSTALLATION SSEMBLY 1: A ..............12 SSEMBLE THE RAME 2: A ................14 SSEMBLE RESS 3: A... -
Page 4: Safety
9. If the machine appears damaged or inoperable, contact a facility staff member to place an “OUT OF ORDER, DO NOT USE” sign on the machine until it is repaired. Only use TRUE supplied replacement components to service this machine. - Page 5 3. Install this piece of equipment on a solid level surface that does not deviate more then 1/8” over a 10’ distance (or as defined and required by local building and architectural codes. 4. TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability.
- Page 6 • Frames and Lifting Arms: Inspect weekly for integrity and function. Replace any component at first signs of wear. Use only TRUE supplied components. 4. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from TRUE free of charge.
-
Page 7: Eneral Are And Dimensions And Weight
Be sure all hardware is tight before using the machine. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your TRUE dealer or TRUE Fitness at (800) 883-8783 or service@truefitness.com. - Page 8 IMENSIONS AND EIGHT “I ” M ACHINE IMENSIONS ACHINE EIGHT AND LOOR OADING EIGHT TACK ONFIGURATION ACHINE WEIGHT PPROXIMATE LOOR OADING 170 lbs. 386 LBS [175 KG] 54 LBS/FT [261 KG/M 250 lbs. 466 LBS [211 KG] 65 LBS/FT [315 KG/M 300LBS (136KG) AXIMUM EIGHT...
-
Page 9: Preparation
REPARATION EQUIRED OOLS Ratchet Wrench and Socket: 9/16” Wrenches: 9/16” (or an adjustable crescent wrench). Rubber mallet. Allen wrenches: (included with the machine) Weight Plate Cartons Depending upon your order, this machine can be assembled with either a 170 lb. or 250 lb. -
Page 10: Ox Arton Ontents
ARTON ONTENTS ITEM UMBER ESCRIPTION FS-CAP-000X TOP CAP FS65-SHD-100X FRONT SHROUD FS-SHD-150X REAR SHROUD FS54-UPR-000X UPRIGHT FS-GRD-100X GUIDE ROD FS54-PAD-100X SEAT PAD FS-PAD-000X BACK PAD FS-BKT-000 GUIDE ROD BRACKET FS-BKT-001 TOP CAP BRACKET FS-WSB-000 WEIGHT STACK BASE... -
Page 11: Box 2 Carton Contents
ARTON ONTENTS ITEM UMBER ESCRIPTION FS65-MFR-000X MAIN FRAME FS65-MFR-100X FRAME, LOWER BRACE FS54-MFR-400X FRAME, REAR BRACE FS65-ARM-000X PRESS ARM FS64-SFR-000X SEAT FRAME FS64-AXL-000 AXLE, PRESS ARM HARDWARE BOX FS-SBR-000X SELECTOR BAR Note: some items shown FS65-CBL-000X CABLE here may be included in FS65-HWR-000X HARDWARE BOX the hardware box. - Page 12 1: A SSEMBLE THE RAME 1. Assemble frame components as shown. ITEM UMBER ESCRIPTION FS54-MFR-400X FRAME, REAR BRACE 2. Loosely assemble ALL hardware shown in this step. FS54-UPR-000X ASSY, UPRIGHT FRAME 3. After aligning all component edges and FS65-MFR-000X ASSY, MAIN FRAME surfaces, tighten the hardware.
- Page 13 1: A SSEMBLE THE RAME 10,6,7,9,8 x2 10,6,7,9,8 x2 DETAIL A DETAIL B 10,6,7,9,8 x2 DETAIL C 10,6,7,9,8 x3 DETAIL D...
-
Page 14: Tep Ssemble
2: A SSEMBLE RESS 1. Assemble the press arm, axle and ITEM UMBER ESCRIPTION hardware. FS65-ARM-000X ASSY, PRESS ARM 2. Fully tighten hardware. FS64-AXL-000 AXLE FS51-MFR-040 WASHER, LARGE OD C 445 SCREW, HH, 3/8 X 1 C 749 WASHER, LOCK, 3/8 C 955A COVER, BASE C 955S... -
Page 15: Ads
3: A SSEMBLE THE 1. Assemble the seat frame, pads and ITEM UMBER ESCRIPTION associated hardware. FS64-SFR-000X SEAT FRAME 2. Fully tighten hardware. FS54-PAD-100X SEAT PAD FS-PAD-000X BACK PAD C 446 SCREW, HH, 3/8 X 1-1/4 C 451 SCREW, HH, 3/8 X 2-3/4 C 749 WASHER, LOCK, 3/8 C 754C... -
Page 16: Weight Plates
4: A SSEMBLE THE EIGHT LATES 1. Install the Weight Stack Bases, ITEM UMBER ESCRIPTION Weight Stack Bumpers, Weight FS-BKT-000 GUIDE ROD BRACKET Stack Washers, and Guide Rods. FS-BMP-001 BUMPER, WEIGHT STACK 2. Install 16 weight plates according to FS-GRD-100X GUIDE ROD ASSEMBLY your order (10 or 15 lb. - Page 17 4: A SSEMBLE THE EIGHT LATES 6, 7, 8 Set the distance between the Collars and the tube as shown Use tape measure 5” DETAIL A DETAIL B...
- Page 18 5: A & P SSEMBLE ABLE ULLEYS 1. Starting at the top plate, ITEM UMBER ESCRIPTION assemble the cable and selector B 900 PULLEY, 4-1/2” pin as shown. Install pulleys and hardware as you go. B 898 PULLEY, 6” 2. Tighten the cable adjustment C 754C WASHER, FLAT, 3/8 bolt to remove slack from the...
- Page 19 5: A & C SSEMBLE THE ULLEYS ABLE 9,4,8,3 9,5,8,3 9,6,7,8,3 9,5,8,3 INSTALL SELECTOR PIN RING AROUND CABLE BOLT AS SHOWN 9,4,8,3 9,5,8,3...
-
Page 20: Step 6: Assemblef
6: A SSEMBLE RONT HROUD 1. Assemble the front shroud as ITEM UMBER ESCRIPTION shown. FS65-SHD-100X SHROUD, FRONT 2. Operate the machine and make C 445 SCREW, HEX HEAD, 3/8 X 1 sure that the weight stack clears C 749 WASHER, LOCK, 3/8 the shroud. - Page 21 7: A SSEMBLE HROUD 1. Set the lower screws of the ITEM UMBER ESCRIPTION shroud into the lower brackets FS-SHD-150X SHROUD, REAR on the upright frame. C 444 SCREW, HEX HEAD, 3/8 X 3/4 2. Then align the holes for the C 754C WASHER, FLAT, 3/8 brackets at the top of the shroud.
-
Page 22: Step 8: Install Top Cap
8: I NSTALL 1. Assemble the bracket to the ITEM UMBER ESCRIPTION top cap as shown. FS-BKT-OO1 BRACKET, TOP CAP 2. Assemble the top cap to the FS-CAP-000X TOP CAP upright frame. C 675D SCREW, BUTTON HEAD, 1/4 X 1/2... -
Page 23: Eight Stack Label
9: I NSTALL THE EIGHT TACK ABEL 1. Select the appropriate weight stack label(s) according to your order. You can install pound labels, kilogram labels, or both. 2. If you ordered a 170 lb weight stack, use labels: LBL-WSE-01170 (for pounds) LBL-WSM-01170 (for kilograms). -
Page 24: Step 9: Install The W Machine Labels
ACHINE ABELS The following are the Warning Labels required for this FS machine. If any of these labels are missing or become damaged, TRUE will replace them free of charge. Note: these labels are not to scale. WARNING WARNING SERIOUS INJURY CAN OCCUR... -
Page 25: Service
B T A I N E R V I C E For warranty service, contact an Authorized TRUE Dealer or a TRUE Customer Service representative at 1-800-883-8783. You can also email us at service@truefitness.com. Before you call, please have the following information ready: •... -
Page 26: Floor
(European) safety standards for stability (without floor anchors) when the machine is used for it’s intended purpose as designated by the manufacturer. However, TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability. -
Page 27: Bolting The Machine To The Warranty
Hours of operation 8:30am - 5:00 pm CST workmanship for a 10 years. The frame is warranted for labor and freight (for parts shipped from TRUE) for one year from date of purchase. * This limited warranty on structural frame does not include paint or coatings. - Page 28 (if anyone other than a TRUE authorized dealer/ technician initially assembles and installs the Product, this The FS-65 comes with one serial number on the base of the Limited Warranty will be void unless the written authorization machine. Please write down your serial number below and keep of TRUE is first obtained).
- Page 29 If you prefer to mail your warranty card, have the owner of the product complete the information below and return it to TRUE Fitness within 30 days from the date of equipment installation.