Napa Carlyle Tools 6-3802A Instruction Manual page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
THIS INSTRUCTION
CONTAINS IMPORTANT SAFETY
INFORMATION.
READ THIS INSTRUCTION
CAREFULLY AND UNDERSTAND
INFORMATION BEFORE OPERATING THIS
TOOL.
• Read and understand all instructions.
Failure to follow all instructions listed
below, may result in electric shock, fire,
explosion and/or serious personal injury. It
is the responsibility of the owner to make
sure all personnel read this manual prior to
using the device. It is also the responsibility
of the device owner to keep this manual
intact and in a convenient location for all
to see and read. If the manual or product
labels are lost or not legible, contact NAPA
for replacements. If the operator is not
fluent in English, the product and safety
instructions shall be read and discussed
with the operator in the operator's native
language by the purchaser/owner or his
designee, making sure that the operator
comprehends its contents.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety Code of
Portable Air Tools (ANSI B186.1) and any
other applicable safety
regulations.
• For safety, top performance and
maximum durability of parts,
operate this tool at90 psig; 6.2
bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact resistant eye,
face & hand protection (Users
& Bystanders) when operating or
performing maintenance on this
tool
• High sound levels can cause
permanent hearing loss. Always
use hearing
recommended by your employer
an OSHA regulations while using
this tool (users and bystanders).
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause
severe injury. Never direct air
at yourself or others. Always
turn off the air supply, drain
hose of air
detach tool from air supply
before installing,
or adjusting any
on this tool, or before performing
any maintenance on this tool.
Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check
for damaged, frayed or loose hoses and
6-3802A
MANUAL fittings, and replace immediately. Do not use
quick detach couplings at tool. See instructions
for correct set-up.
MANUAL • Keep tool out of reach of children.
ALL
periods of time may be harmful to your hands
and arms. Discontinue use of tool if discomfort,
tingling feeling o pain occurs. Seek medical
advice before resuming use.
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and
firm. Do not overreach when operating the
tool.
• Do not point or indulge in any horseplay with
this tool.
• Anticipate and be alert for sudden changes in
motion during start up and operation of any
power tool.
• Tool shaft may con tin ue to ro tate brief ly af ter
codes and
throt tle is re leased. Avoid di rect con tact
with ac ces so ries dur ing and af ter use. Gloves will
re duce the risk of cuts or burns.
kept away from tool and accessories. Choking
can occur if neckwear is no kept away from
tool and accessories.
• Correct cut-off wheel mounting is necessary
to prevent injury from broken wheels. Do not
use chipped or cracked cut-off wheels.
off wheels should be a free fit on the spindle
protection as
to prevent stress at the hole. Use only wheel
collars that come with the tool for mounting
the cut-off wheel.
adapters may over stress the wheel. Tighten
the wheel on the spindle to prevent spin off
when the tool is turned off.
• When using the cut-off tool, be careful not
to exert excessive force.
could be hazardous if it causes the tool spindle
to bend or break. The burning of the work
piece or excessive speed reduction indicates
too much force being applied. Start the tool
off the work, set it down on the work evenly
and move in the direction desired to make the
pressure and
cut. When finished cutting, lift off the work
before stopping the motor.
removing
• Never operate this tool without required disc
accessory
cover/guard in place.
RPM RPM RPM
WARNING
• Air powered tools can vibrate
in use. Vibration, repetitive motions or
uncomfortable positions over extended
• Slipping, tripping
or falling while operating air tools can
be a major cause of serious injury or
• Do not carry tool by the hose.
Protect the hose from sharp
objects and heat.
• Keep away from rotating end
of tool. Do not wear jewelry or
loose clothing. Secure long hair.
Scalping can occur if hair is not
Flat washers or other
Too much force
• RPM of the accessory must
exceed tool rpm. Use accessories
rated at 21,000 rpm or higher.
2
• Use accessories recommended by NAPA
tools.
• Do not lu bri cate tools with
flam ma ble or vol a tile liq uids such
as ker o sene, die sel or jet fuel.
• This tool is not insulated against
electric shock.
• This tool must not be used in
explosive atmospheres.
• Servicing and repairs should only
be made by an authorized service
and
center.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace
damaged labels.
• Do not lock, tape or wire the "on/off"
safety lever in the "on" position, as the
lever must be free to return to the "off"
position when released.
• Failure to heed these warnings may reusult
in personal injury and/or property damage.
WARNING:
expose you to chemicals including
nickel which is known to the State of
California to cause cancer and birth defects or
other reproductive harm. For more information
go to www.P65Warnings.ca.gov.
Cut
This product can
Rev. 09/09/19