Table of Contents
Advertisement
Installation and connection
en
For your safety (only for ZA)
This appliance is adjusted to operate on LPG only.
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas
installation, you must
immediately shut off the gas supply and/or close the
■
gas cylinder valve
immediately extinguish all naked flames and
■
cigarettes
switch off electrical appliances and lights
■
open windows and ventilate the room
■
call the aftersales service or the gas supplier
■
Burn back
Fire in burner tube or chamber
In the event of a burn-back, where the flame burns back
to the jet, immediately turn off the gas supply at the
control valve on the panel.
After ensuring the flame is extinguished, re-light the
appliance in the normal manner.
Should the appliance again burn back, close the control
valve and call a service technician. Do not use the
appliance again until the service technician has
declared that it is safe to do so.
Gas-pressure regulator
This appliance requires an operating pressure of 2,8
kPa at the appliance. A suitable LPG regulator that
coplies with the requirements of SANS 1237 must be
installed.
Important information for the user
This appliance may only be installed by a registeres
LP Gas installer.
All registered installers are issued with a card carrying
their registration number. Ask to be shown the card
before allowing the installation work to be shown the
card before allowing the installation work to commence
and make a note of the installer QCC number.
Upon completion of the installation, the installer is
required to explain the operational details of the
appliance together with the safety instructions.
You should only sign for acceptance of the installation
and be provided with a copletion certificate. You should
only sign for acceptance of the installation when the
installation is completed to your satisfaction.
Note that your invoice is required in the event that you
wish make a quarantee claim.
Important information for the installer
This appliance may only be installed by a registered LP
Gas installer registered with the Liquefied Petroleum
Gas Association of Southern Africa.
The appliance must be installed in accordance with the
requirements of SANS 10087-1 and any fire department
regulations and/or local bylaws applicable to the area. If
in doubt check with the relevant authority before
undertaking the installation.
Upon completion of the installation you are required to
fully explain and demonstrate to the user the
10
operational details and safety practices applicable to
the appliance and the installation.
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line;
the gas pipe could be damaged. There is a risk of a gas
leak! Do not move the appliance while holding it by the
door handle. The door hinges and door handle could
be damaged.
Electrical connection
The appliance is designed to operate at 220-240 V. A
16 A fuse is required for connection.
Have the appliance installed by your after-sales service.
Any damage arising from the appliance being
connected incorrectly will invalidate the warranty.
Caution!
If the electricity supply drops below 180 V, the
■
electrical ignition system does not work.
If the supply cord is damaged, it must be replaced
■
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
:
Warning – Danger of death!
There is a risk of electric shock if you touch live
components.
Always make sure your hands are dry when you
■
touch or hold the mains plug.
Only pull out the mains cable by taking hold of the
■
plug and removing the plug; never pull it out by the
mains cable itself, as this could damage it.
Never unplug the mains plug when the appliance is
■
in operation.
Please note the following information and ensure that:
Notes
The mains plug fits the socket.
■
The cable cross section is adequate.
■
The earthing system is properly installed.
■
The mains cable is only replaced by a qualified
■
electrician (if this is necessary).Spare mains cables
can be ordered from our after-sales service.
No power strips/multi-way connectors or extension
■
cables are used.
If using a residual current device, only use one that
■
bears the mark
.
z
The presence of this mark is the only way to be sure
that it fulfils all the applicable regulations.
The mains plug can be accessed at all times.
■
The mains cable is not kinked, crushed, modified or
■
severed.
The mains cable does not come into contact with
■
heat sources.
Advertisement
Table of Contents
