Advertisement
children of less than 3 years old should be kept away unless continuously supervised.
9
nOte: children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed
or installed in its intended normal operating position and they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
nOte: this appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. children shall not play with the appliance. cleaning and
user maintenance shall not be made by children without supervision.
2. intrOduCtiOn
P
Powder coated metal cabinet with two ruby halogen infrared elements and chemically polished reflectors for maximum heat emission. controllable
power output by rocker switches on the side of the cabinet. features easy-rolling swivel castors with 2 locking castors. suitable for wide range of
heating including restorative applications. supplied with power cable and 32Amp/110V plug.
3. SpeCifiCatiOn
specifications
model no. ........................................................... irs153110V
Power output (2 heat settings) ........................... 1500/3000W
size WxdxH ............................................600 x 620 x 815mm
supply .....................................................................110V-32A
Weight: ...................................................................... 14.49kg
4. aSSeMbLY
4.1.
fit the handle section of the support frame to the wheel section ensuring the fixing
holes align.
4.2.
fit the heater to the support frame using the bolts provided, ensuring the shaped spacers are
fitted either side of the frame as shown. tighten the bolts sufficiently to retain the heater at the
required angle.
4.3.
remove the front grille by unscrewing the retaining screws.
warninG! never touch element glass directly with fingers, only touch the ceramic ends
‰
or use a soft cloth, to prevent damage.
4.4.
carefully insert each element into the two push-in side fittings with a gentle pressure.
4.5.
check the element is properly locate, then replace front grille.
5. OperatiOn
5.1.
Place the heater on a level floor in the area you require to heat. Allow a minimum of 2mtr between the heater and adjacent objects.
5.2.
Plug the heater into the mains supply and select the required output by using the two rocker switches on the side which switch the
elements on and off. each lamp has an output of 1500W.
5.3.
to switch the unit off, select "0" on both the rocker switches and unplug from the mains. Allow the unit to cool before handling or storage.
warninG! dO nOt touch the top of the heater when in use as it becomes hot.
‰
warninG! Always allow elements to cool before moving the units. use only on a smooth even surface. failure to do so will cause premature
‰
wear to the lamps and reduce their working life.
5.4.
the heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted beyond 35° either forwards or backwards.
this prevents fire in the event of the unit being knocked over. if the unit does not turn on again when returned to the vertical, tip it
approximately 35° in the opposite direction until you hear the internal switch operate. As the heater switches on return it to the vertical.
6. MaintenanCe
warninG! Before attempting any maintenance ensure the unit is unplugged from the mains power supply, it is cool and on level
‰
ground.
dO nOt touch the element glass, even when cold.
8
dO nOt use the heater with out the grilles fitted.
8
6.1.
To clean the reflector, remove the front grill by unscrewing the retaining screws and wipe the reflector with a clean dry cloth. dO nOt
use abrasives or solvents. The surface of the reflector is very soft and scratches may cause it to overheat. Replace the grille.
6.2.
to change the element remove the front grille by unscrewing the retaining screws.
6.2.1.
ease the sprung sockets on the ends of the element back and pull the element forward so that it clears the socket, remove element.
warninG! never touch element glass directly with fingers, only touch the ceramic ends or use a soft cloth, to prevent damage.
‰
6.2.2.
carefully insert the replacement lamp into the two push in side fittings with gentle pressure.
6.2.3.
check the element is properly located, then replace front grille.
© Jack sealey limited
i
Original Language Version
irs153110V | issue3(1) 22/05/18
Advertisement
