Ryobi R18RT Original Instructions Manual
  1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Power Tool
  5. R18RT
  6. Original instructions manual

Ryobi R18RT Original Instructions Manual

Hide thumbs Also See for R18RT:
Table of Contents

Advertisement

Quick Links

ORIGINAL INSTRUCTIONS
Rotary Tool
R18RT

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R18RT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ryobi R18RT

Summary of Contents for Ryobi R18RT

  • Page 1 ORIGINAL INSTRUCTIONS Rotary Tool R18RT...
  • Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.

  • Page 3: Intended Use

    Safety, performance, and dependability have been given ■ When operating a power tool outdoors, use an top priority in the design of your rotary tool. extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • Page 4 Store idle power tools out of the reach of children SERVICE ■ and do not allow persons unfamiliar with the power ■ Have your power tool serviced by a qualified repair tool or these instructions to operate the power tool. person using only identical replacement parts.
  • Page 5 hearing protectors, gloves and workshop apron Pinching or snagging causes rapid stalling of the rotating capable of stopping small abrasive or workpiece accessory which in turn causes the uncontrolled power tool fragments. The eye protection must be capable of to be forced in the direction opposite of the accessory’s stopping flying debris generated by various operations.

  • Page 6: Additional Safety Warnings

    kickback may propel the spinning wheel and the power ■ The recommended ambient temperature range for the tool directly at you. charging system during charging is between 10°C and 38°C. ■ When wheel is pinched, snagged or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until ADDITIONAL SAFETY WARNINGS the wheel comes to a complete stop.

  • Page 7: Risk Reduction

    ■ Injury caused by dust accessories if they become damaged or unbalanced. – Wear appropriate dust control mask with filters LEARNING TO USE THE ROTARY TOOL suitable for protecting against particles from the Hold the pen in your hand and get used to its weight, material being worked on and abrasive particles balance, and the taper of the housing.

  • Page 8: Symbols In This Manual

    SYMBOLS IN THIS MANUAL Please read the instructions carefully before starting the machine. Regulatory Compliance Mark (RCM). Note Product meets applicable regulatory requirements. Parts or accessories sold separately Failure to keep long hair away from air inlet could result in personal injury. The following signal words and meanings are intended to explain the levels of risk associated with this product: Wear eye protection...
  • Page 9 ACCESSORY Figure Accessory Accessory number Application Drum sander mandrel (Ø 6.4 mm) (Ø 3.2 mm shank/collet) Attaching to sanding drums Drum sander mandrel (Ø 12.7 mm) (Ø 3.2 mm shank/collet) Removing and Wrench inserting accessory bits 15.9 mm. x 9.5 mm orange 120-grit aluminum oxide grinding wheel bits Grinding metal 9.5 mm x 12.7 mm orange 120-grit aluminum oxide...
  • Page 10 ..

  • Page 11: Know Your Product

    KNOW YOUR PRODUCT 1. Battery port 6. Pen holder 2. Accessory storage slots 7. Spindle lock lever 3. Speed control dial 8. Flex shaft 4. On/off switch 9. Key hole hanger 5. Collet nut 127 mm(5”)
  • Page 14 127 mm(5”) 229 mm...

  • Page 15: Product Specifications

    PRODUCT SPECIFICATIONS BATTERY AND CHARGER Rotary tool Compatible battery pack Compatible charger Model (not included) (not included) Model R18RT Voltage 18 V RB18L13 BCS618G RB18L15 BCL14181H Collet 3.2 mm(1/8“) RB18L20 BCL14183H RB18L25 BCL1418IV* Flexshaft length 91.5 cm Lithium-Ion RB18L30A RC18150...
  • Page 16 Imported by: Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited 2 Landing Drive, Mangere RYOBI is a trademark of Ryobi Limited, Auckland, 2022, New Zealand and is used under license. 961075460-01...

Table of Contents