Advertisement
Thank you for purchasing a Sealey plasma inverter. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: BEFORE USING THIS PRODUCT, PLEASE READ THE INSTRUCTIONS CAREFULLY. MAKE CAREFUL NOTE OF SAFETY INSTRUCTIONS, WARNINGS
AND CAUTIONS. THIS PRODUCT SHOULD ONLY BE USED FOR ITS INTENDED PURPOSE. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1.
INTRODUCTION & SPECIFICATIONS
1.1.
Introduction
Inverter power supply fitted with plasma cutter control circuitry. Inverter features four LED information panel including torch
under voltage, air fault, general fault (thermostat, over/under-voltage, over current) and power on. Supplied with plasma torch and
earth cable. Features regulated push button arc that avoids having to touch the work piece. Ideal for cutting steel, stainless,
galvanised steel, aluminium, copper and brass. Includes integral regulator unit with panel-mounted pressure gauge. IP21S Rated.
1.2.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . .PP40H
Power Output: . . . . . . . . . . . . . . . . . . . . . .15-40A
Duty Cycle: . . . . . . . . . . . . . . . . . . . . .35% @ 40A
Air Requirement: . . . . . . . . . . . . . . . . . 300ltr/min
Air Pressure:. . . . . . . . . . . . . . . . . . . . . . 45-70psi
Supply Voltage: . . . . . . . . . . . . . . . . . 230V - 1ph
Power Absorbed: . . . . . . . . . . . . . . . . . . . . 5.7kW
Insulation Class: . . . . . . . . . . . . . . . . . . . . . . . . . F
Protection: . . . . . . . . . . . . . . . . . . . . . . . . . IP21S
2.
SAFETY INSTRUCTIONS
2.1.
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We
also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that
are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a
Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
2.1.1.
The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
2.1.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
2.1.3.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 2.1.1. and 2.1.2.
and use a Portable Appliance Tester.
2.1.4.
Ensure that cables are always protected against short circuit and overload.
2.1.5.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none are loose.
2.1.6.
Important: Ensure that the voltage marked on the appliance matches the power supply to be
used and that the plug is fitted with the correct fuse - see rating at right.
DO NOT pull or carry the appliance by the power cable.
2.1.7.
2.1.8.
DO NOT pull the plug from the socket by the cable.
2.1.9.
DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired
or replaced by a qualified electrician.
2.1.10.
This product will require more than a 13Amp electrical supply for full performance, so a plug
is not fitted. It is a single phase machine and must be run from a 32Amp supply for full performance. We recommend you discuss the
installation of an industrial round pin plug and socket with a qualified electrician.
Fit a plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above. DO NOT connect either wire to the earth terminal.
WARNING! Reminder, the electrical installation of the plasma cutting unit must only be carried out by a qualified electrician.
WARNING! Be very cautious if using a generator to power the inverter. The generator must be self regulating and stable with regard
to voltage, waveform and frequency. The output must be greater than the power consumption of the inverter. If any of these
requirements is not met the electronics within the inverter may be affected.
NOTE:
The use of an unregulated generator may be dangerous and will invalidate the warranty.
WARNING! The inverter may produce voltage surges in the mains supply which can damage other sensitive equipment
(e.g. computers). It is recommended that the inverter is connected to a power supply that does not feed any sensitive equipment.
2.1.11.
If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm²,
but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output
sockets, we recommend the use of 2.5mm² section cable.
© Jack Sealey Limited 2013
INSTRUCTIONS FOR:
PLASMA INVERTER 40AMP 230V
MODEL No: PP40H
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.54kg
Max. Cutting Capacity (Carbon Steel):. . . . 10mm
Accessories Included*: . . . . . . . . . . . . . . . . . . Yes
*Plasma Torch and Earth Cable
, are fitted with live (brown) and neutral (blue) wires only.
Original Language Version
230V 1ph
THE PLASMA INVERTER
MUST BE CONNECTED TO A
32AMP SUPPLY FOR
MAXIMUM OUTPUT
PP40H
Issue: 1 - 08/05/13
Advertisement
