Sealey Power Tools SA36.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Follow all workshop Health & Safety rules, regulations and conditions when using this tool.

WARNING! Disconnect from air supply before servicing.

Maintain tool in good condition and replace any damaged or worn parts. Use genuine parts only.

Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use

and ensure that all connections are secure.
WARNING! Always wear approved eye and face protection when operating the tool.

Wear ear defenders and gloves if necessary.

Keep hands and body clear of the workpiece when operating the tool.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Secure unstable workpiece with a clamp, vice or other adequate holding device.

Keep children and non-essential persons away from the work area.

DO NOT get the tool wet or use in damp or wet locations.

DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.

DO NOT use the tool for a task it is not designed to perform.

WARNING! DO NOT use the tool if damaged or faulty. Contact your local service agent.

DO NOT use the tool unless you have been instructed in its use by a qualified person.

DO NOT carry the tool by the air hose, or yank the hose from the air supply.

 DO NOT direct air from the air hose at yourself or others.
 DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
 When not in use, disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATION
2.1. Introduction
Suitable for heavy bodyshop use. Aluminium alloy body with steel punch and die. Puts a 10mm
flange onto car-panel-thickness sheet for lap jointing and puts 6mm holes in panels for mig spot-
welding.
2.2. Specification
Operating Pressure:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi (6.2 bar)
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ¼"BSP
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3kg
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.57m/s²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74dB(A)
Spare Punch: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA36.V2-06
Spare Die: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA36.V2-03
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR PUNCH/FLANGE TOOL
SA36.V2
MODEL No:
Original Language Version
SA36.V2 Issue: 3(SP) - 05/09/13