Summary of Contents for HL-Tech WL-3002B
- Page 1 WLAN 802.11 b/g MiniPCI WL-3002B Hardware Installation and Configuration Utility User’s Guide Integrated Baseband and MAC Solution IEEE 802.11b/g WLAN...
-
Page 2: Table Of Contents
Contents: Table of Contents . .……….………..……….…………...2 ……… Introduction ………… …………………………..3 … ………… … Install the WLAN card in PC/NB …….……….….………..4 …… Install WL-3002B driver…….………………….…….…………..5 Setup WL-3002B Configuration Utility… ……….…………….7 … HL-TECH Corporation... -
Page 3: Introduction
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. HL-TECH Corporation... -
Page 4: Install The Wlan Card In Pc/Nb
Install the WLAN card in PC/NB Release the screw from PC/NB Find out the pre-wired cable Connect the cable with Mini-PCI Align and firmly plug the Mini-PCI card into the slot. Re-place the cover to PC/NB Secure the screw with a cross screwdriver. HL-TECH Corporation... -
Page 5: Install Wl-3002B Driver
Install WL-3002B driver The program will automatically proceed with Press “Next” to continue installing. Press “Browser” to change the folder where setup Select or create a program folder and press will install files or press “Next” to continue. “Next” to continue. - Page 6 Insert the Wireless Card to slot of NB and c hoose Press “Continue” to continue the process. “Install the software automatically (Recommended)” and press “Next”. Press “Finish” to complete the installation HL-TECH Corporation...
-
Page 7: Setup Wl-3002B Configuration Utility
Setup WL-3002B Configuration Utility 1. Station: Figure 1-1 Open the WL-3002B Configuration Utility shown as Figure 1-1. The adapter can be set at “Station” or “Access Point” Mode from the Mode drop down menu. Station mode is selected for the item. - Page 8 Select the “Ad_Hoc” or “Infrastructure” Mode by the “Network Type” drop down menu. Select the “Enable WEP” or “Disable WEP” by the “Encryption” drop down menu. Select the “Open System” , “Shared Key” mode or “Auto” from the “Authentication Mode” drop down menu. HL-TECH Corporation...
- Page 9 Modify the 4 sets key depending on the selected key length on the field of “Key Value”. The key value is used the hexadecimal format. Select which key format “hexadecimal” or “ASCII” will be used from the “Key Format” HL-TECH Corporation...
- Page 10 If you select “pre-share-key” protocol , you can write down your password on the filed of “Passphrase” , the password length can be selected from 8 bytes to 63 bytes (ASCII format) depend on user . HL-TECH Corporation...
- Page 11 “Profile name”, and press the “Save Current” button to save the current status on the profile. Select the profile name that wanted to delete from the “Profile name” drop down menu, and press “Delete” button to delete it HL-TECH Corporation...
- Page 12 Threshold” bar, drop and move cursor to set the fragmentation threshold point, the range is from 256 to 2346 bytes. “RTS / CTS Threshold” bar, drop and move the cursor to set the RTS threshold point, the range is from 0 to 2347 bytes. HL-TECH Corporation...
- Page 13 2. Access Point Figure 2-1 Open the WL-3002B Configuration Utility shown as Figure 2-1. For the soft AP, please option the “ Access Point” from drop down menu Mode filed. “Network Adapter” shows the available WLAN card for soft AP.
- Page 14 Adapter”. If the bridge function will be disable, please select the “ No bridge” item from “Bridge Adapter”. Note: The maximum number of channels permitted by local regulations: 1 ~ 11channels for the United States / 1~13 channels for the EU. HL-TECH Corporation...
- Page 15 Modify the 4 sets key depending on the selected key length on the field of “Key Value”. The key value is used the hexadecimal format. Select which key format “Hexadecimal” or “ASCII” will be used from the “Key Format”. HL-TECH Corporation...
- Page 16 Select “Disable” or “Accept” or “Filter” from the filed of drop menu “Filter Type”. There are 16 sets MAC addresses can be filled on the “Filter MAC Address”. If all setting is finished, please press Apply to save it. HL-TECH Corporation...
- Page 17 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: “Contains TX FCC ID: SLH-WL-3002B” End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna...
- Page 18 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)•This device may not cause harmful interference and (2)•This device must accept any interference received, including interference that may cause undesired operation IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product.
Need help?
Do you have a question about the WL-3002B and is the answer not in the manual?
Questions and answers