SELF-PRIMING PUMPS
FEATURES
Pump Type:
Pedestal Pump
Body:
316 Stainless Steel
Impeller:
Neoprene or EPDM
Shaft Seal:
Mechanical; Carbon-on-Ceramic
or Tungsten Carbide; Nitrile
Ports:
1" ACME Threads with Bevel Seat
or Clamp Type
Shaft:
316 Stainless Steel
Weight:
5.5 lb (2.5 kg) Approx.
APPLICATIONS
DAIRY: Transfer and processing of raw milk, cream, milk
whey, buttermilk, condensed milk.
FOODS: Processing of eggs, sugar liquors, brines, catsup,
chocolate, glaze, gelatin, honey, jams, jellies, mayonnaise,
molasses, mustard, pickle relish, vinegar, water, yeast
slurries, syrups, liquids containing solids in suspension
such as chopped tomatoes, nuts, peanut butter.
BEVERAGE: Circulating and transferring alcohols, beers,
brewery slop, cider, distillery wort, extracts, flavors, juice,
mash, soft drink syrups, wines.
PHARMACEUTICAL: Moving medicines, cosmetics,
process chemicals, lotions, preparations, filtering solutions,
used as a filling line supply pump.
WARNING
!
Explosion hazard. Do not pump gasoline, solvents,
thinners or other flammable liquids. To do so can
cause an explosion resulting in injury or death.
OPERATING INSTRUCTIONS
1. INSTALLATION – Pump may be mounted in any
position. The rotation of the pump shaft determines
the location of the pump's intake and discharge
ports. (Refer to dimensional drawing.) Pump is
normally assembled at factory for clockwise rotation
looking at end cover. If counterclockwise rotation is
desired, follow steps 1 and 2 of disassembly and
step 9 of assembly instructions to change direction
of impeller blade deflection under cam.
2. DRIVE – Belt or direct with flexible coupling.
Belt Drive: Overtight belt load will reduce pump
bearing life.
Direct Drive: Clearance should be left between
WARNING
!
Injury hazard. Exposed pulleys and belts can
cause injury. Install shield around pulleys and
belts. Stay clear while machinery is operating.
Models 30550-0XXX
VARIATIONS AVAILABLE
Model
30550-0005 Standard Pressure, Neoprene Impeller,
Carbon Seal, ACME Ports
30550-0015 High Pressure, Neoprene Impeller,
Carbon Seal, ACME Ports
30550-0105 Standard Pressure, Neoprene Impeller,
Tungsten Carbide Seal, ACME Ports
30550-0115 High Pressure, Neoprene Impeller,
Tungsten Carbide Seal, ACME Ports
30550-1005 Standard Pressure, Neoprene Impeller,
Carbon Seal, Clamp Ports
30550-1015 High Pressure, Neoprene Impeller,
Carbon Seal, Clamp Ports
30550-1105 Standard Pressure, Neoprene Impeller,
Tungsten Carbide Seal, Clamp Ports
30550-1115 High Pressure, Neoprene Impeller,
Tungsten Carbide Seal, Clamp Ports
drive shaft and pump shaft when installing coupling.
Always mount and align pump and drive shaft before
tightening the coupling set screw.
If pulley or coupling must be pressed on shaft,
remove end cover and impeller to support shaft from
impeller end during press operation. Do not hammer
pulley or coupling on shaft; this may damage bearing
or seal.Capacitor start motor is required to
overcome starting torque of impeller.
3. SPEEDS – 100 RPM to the maximum shown in the
performance curves. For longer pump life, operate
at lowest possible speeds. Lower speeds are
required for viscous liquids. Consult the factory for
proper speeds and horsepower requirements.
30550-1XXX
Description