Subscribe to Our Youtube Channel
Summary of Contents for Graphic Whizard Finishmaster 100
- Page 1 Graphic Whizard FinishMaster 100 Perforate Score and Slit Machine Instruction Manual...
-
Page 2: General Operation
6635 Kitimat Rd, Unit #34; Mississauga, Ontario; Canada L5N 6J2; Tel: (905) 858-7663 Fax: (905) 858-4419 Toll Free 1-800-265-3376 Web Site: www.graphicwhizard.com FINISHMASTER 100 REFERENCE MANUAL Version 9902 1.0 General Operation... -
Page 3: Machine Assembly
The FinishMaster 100 can perforate, score or slit single sheets (13# bond to 12 point card or 45 to 250 gsm paper) or multi-part carbonless forms (up to 10 parts) With proper setup, thousands of sheets per hour can be quickly and identically processed. The unique friction feeder sends through one set at a time, even from the unglued side of a padded set. - Page 4 the pieces on the tray. For the exit tray, place the tray side guides, bottom flange towards the center. The magnetic strips on the bottom of the tray side guides, will secure them to the exit tray. The operator side tray guide of both the feed and exit tray should be pulled all the way over to the operator side.
-
Page 5: Setting Up A Job
Setting Feed Tire Pressure The friction feed system used in EXIT automatic Graphic Whizard machines TIRES is unique. It utilizes three top feed << SAFE >>... - Page 6 Once the feed tray and side tray guides have been assembled according to the sheet width required, you may locate the feed tires along the feed shaft. For proper sheet feeding, the position of the three feed tires along the width of the sheet is also important. Loosen the set screws of the feed tire hubs using the small hexdriver provided in the accessory kit.
- Page 7 ahead of the other. Place the leading edge of the first sheet under the feed tires. Slowly tighten the feed tire pressure adjusting screws while jiggling the pages back and forth. The correct setting is achieved when the second page is no longer able to run under the feed tires.
- Page 8 Perforating, slitting and/or scoring can be performed quickly and easily. The perforator blades are available with 2, 4, 6, 8 and 12 teeth per inch as well as Microperf. The blades can be easily interchanged using the ring pliers supplied with the machine. Remove the accessory holder (see Figure 7) from the machine.
- Page 9 sure the sheet travels through the machine square. If you adjust the operator side tray guide, you must adjust the non-operator side tray guide as well. Run a few more sheets through and check the sheet again. Continue until the perforation lines up. Now, take the lead edge of the sheet and fold it over to the last inch of the sheet.
-
Page 10: Running The Machine
The main rollers are comprised of a bottom solid roller and 6 adjustable rollers on top. The top rollers are mounted on a spring loaded shaft, to maintain pressure down to the bottom solid roller. The adjustable top rollers must be distributed along the shaft so that a majority will be in contact with stock as it passes through to ensure proper transport. -
Page 11: Cleaning And Maintenance
The efficiency of the feeding can be improved by increasing the spacing between the sheets of your fanned stack. Begin with small stacks (10 to 20 sheets) and build up to larger stacks as you become more confident with your fanning. Once you have mastered the art of fanning, you can progress to back-feeding to provide continuous feeding and uninterrupted operation. - Page 12 Ensure that the trays and guides are clean. Lubrication The FinishMaster 100 utilizes eight oil-impregnated bronze bushings to support all shafts. An occasional drop of light machine oil will maintain their lubricating qualities. Wipe off any excess oil to avoid spoiling a job.
Need help?
Do you have a question about the Finishmaster 100 and is the answer not in the manual?
Questions and answers