Advertisement
3. Replace filter coping. Put the twelve nuts and washers onto each of the twelve bolts, then screw all the nuts on with
wrench,ensuring that all nuts are tight.
a. Carefully screw pressure gauge (with O'ring in place) into tapped hole in the filter coping. Do not over-tighten.
b. Ensure air relief valve (with O'ring in place) is tight fit to filter coping and turn it easily.
4. Connect pump to control valve opening marked PUMP.
5. Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary
plumbing connections, suction lines to pump, waste, etc.
6. Make electrical connections to pump per pump instructions.
7. To prevent water leakage, be sure all pipe connections are tight.
MAIN DIMENSION
DIMENSION TABLE
High
Diameter
Valve Port
Model
mm
mm
Size
A
B
Inch
S900(C)
1180
920
2.5"
INSTALL/START-UP OF FILTER
1. Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
always depress handle before turning.)
3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial
back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about
1/2 to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the
filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the
initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control
valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
Sand
Kg
470
B
2-4
1
9
12
13
10
11
A
Item No.
Part No.
01013003 Handle (Big)
1
2
03018008 Pin for Handle
3
01181027 Washer for Handle(White)
4
89281204 M6*33 T Screw with Nut
5
01021129 2.5"Side Mount Valve Standard Lid(White)
6
02010228 O-Ring for 2.5" Valve Lid
7
02011022 O-Ring for 2.5" Valve Rotor
8
01181002 Washer for Spring(White)
9
03014025 Spring for 2.5" Side Mount Valve
10
89280806 2.5" Valve Rotor With Spider Gasket
11
01021128 2.5" Side Mount Valve Bottom Body(White)
12
02020053 O-Ring for 2.5"Union
01171159 2.5" Union (White)
13
14
01150180 2.5" PVC Tube 90mm
15
01150181 2.5" Elbow Tube
16
01150180 2.5" PVC Tube 270mm
01013147 2.5"Connector (Black)
17
01051243 2.5"Connector (white)
01171158 2.5"Union (A/E)(white)
18
19
02010043 O-Ring for Union Adaptor
01013142 2.5" Side Mount Valve Plug (White)
20
21
89280104 Sight Glass With O-Ring
22
01111048 Connector for Pressure Gauge/Stopper(White)
23
89021303 Drain Plug with O'Ring(White)
24
01013143 2.5"Connector(White)
REPLACEMENT PARTS OF FILTER
Key No. Part No.
1
06011032 Oil Pressure Gauge With O-ring (40 psi)
2
01111048
3
2
89010701 Air Release Valve
4
3
89010601
5
4
01172005 Lid (Grey Colour)
6
5
02011126 Filter Neck Gasket
6
89011315 S900C Filter Tank With Base
7
89280804 2.5"Side Mount Valve
7
8
89280117 Connector Plate Side Mount
9
89011316 S900C Top part of the inner tank system
8
10
89011317
14
11
89011318 Laterals (233mm&115mm)
12
01110030 Tank System Support
13
89011207 S900 Air Vent Pipe
14
89010107 Water Drain Set
REPLACEMENT PARTS OF MULTIPORT VALVE
Product Description
Qty
1
1
1
12
1
1
2
1
1
1
1
7
2
2
1
1
2
3
5
5
2
1
2
2
3
3-4
Qty
Product Description
1
Connector for Pressure Gauge/Stopper
1
1
03013003 M8 Nut*12Pc; + 03012003 M8
1
Washer*12Pc;
1
1
1
1
1
1
S900C Bottom part of the inner tank system
1
8
2
1
1
1
2
3
4
5
6
7
8
9
10
24
23
22
11
12
19
18
17
14
13
12
21
13
20
14
15
19
18
17
16
Advertisement
