Download Print this page
Crunch PX-1000.2 Quick Start Installation Manual

Crunch PX-1000.2 Quick Start Installation Manual

Advertisement

Quick Links

Quick Start
Installation Guide
Congratulations on your choice of a Crunch amplifier. This
"Quick Start Installation" guide is meant to help you "hook
up" and play music.
Setup
The input MODE switch will "sum" or
A
combine the right and left channel signals
in the MONO position to improve bass
Input Mode
performance. Select MONO only when the
amp is being used for subwoofers.
The XOVE
R Mode switch sets the typ
B
of crossover that will be active. 4 channel
models will have two switches, one for each
Xover Mode
set of channels.
C
The HPF(hig
h pa
ss filter) control will limit the
output below the selected frequency. This
High pass
is typically used to protect midrange and hi
frequency speakers from damage and to
Adjustment
allow a smooth transition from a subwoofer.
The LPF(low pass filter) control will limit
D
output above the selected frequency. This
is used to allow a smooth transition to the
Low pass
higher frequency speakers.
Adjustment
The BASS BOOST or BASS EQ control
E
will increase the output at 45Hz for more
pronounced bass. Exercise caution.
Bass Boost
Increase the level in small amounts until
distortion is noticed, then back off a little.
Some models include a bass
F
remote. Avoid adjusting the bass
remote while operating vehicle.
Remote Level
Control
G
This is a critical step to insure your amplifier
is properly adjusted to match the signal
output level of your source unit.
Level Setting
THIS IS NOT A VOLUME CONTROL!
1.
If possible, with the source unit off, confirm that the primary volume control is
turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or "0" adjustment. Make sure that the green
the end of the amplifier is illuminated.
3.
Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the
of the source unit up.
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or
until you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier level (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple amplifiers.
Common System Setup
2ch - Full Range
MODE
XOVER
MONO STEREO
FULL LPF HPF
e
XOVER
4ch -
Full
Range
FULL LPF HPF
XOVER
HPF
FULL LPF HPF
30Hz
XOVER
60Hz 1.2KHz
FULL LPF HPF
30Hz
LPF
4ch
- Mixed Mono
30Hz
250Hz
XOVER
BRIDGED
BASS
LEFT
RIGHT
FULL LPF HPF
BOOST
30Hz
XOVER
FULL LPF HPF
30Hz
0dB
9dB
SPEAKER
OUTPUT
Mono
SUB
SONIC
LEVEL
15Hz
55Hz
BRIDGED
LEFT
RIGHT
6V
0.2V
SPEAKER
OUTPUT
is
LED
on
volume
XOVER
INPUT
LEVEL
SUBSONIC
SUBSONIC
FULL
HP
LP
9V
0.2V
15
35Hz
10
40Hz
XOVER
PHASE
LPF
LPF
LPF
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
LEFT
RIGHT
MODE
MONO STEREO
SPEAKER
OUTPUT
BRIDGED
BRIDGED
LEFT
RIGHT
LEFT
LEFT
RIGHT
LPF
HPF
SPEAKER
OUTPUT
SPEAKER
SPEAKER
250Hz
60Hz
1.2KHz
SPEAKER
OUTPUT
SPEAKER
OUTPUT
LPF
HPF
250Hz
60Hz
1.2KHz
BRIDGED
LEFT
LEFT
RIGHT
LPF
HPF
BRIDGED
LEFT
RIGHT
BRIDGED
LEFT
SPEAKER
OUTPUT
BRIDGED
250Hz
60Hz
1.2KHz
SPEAKER
LEFT
LPF
HPF
250Hz
60Hz
1.2KHz
SPEAKER
OUTPUT
SPEAKER
SPEAKER
LOW
PASS
SPEAKER
OUTPUT
30Hz
250Hz
SPEAKER
OUTPUT
SPEAKER
MODE
MONO STEREO
MODE
BRIDGED
RIGHT
OUTPUT
OUTPUT
BRIDGED
RIGHT
RIGHT
OUTPUT
RIGHT
OUTPUT
OUTPUT
OUTPUT

Advertisement

loading
Need help?

Need help?

Do you have a question about the PX-1000.2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Crunch PX-1000.2

  • Page 1 “0” adjustment. Make sure that the green the end of the amplifier is illuminated. Congratulations on your choice of a Crunch amplifier. This Play a clean musical selection of which you are very familiar. CD is preferred.
  • Page 2 BRIDGED LEFT RIGHT LEFT RIGHT Model Fuse Size Cable Size Power Power / Ground Connections cable size PX-1000.2 1-40A Smaller amps SPEAKER OUTPUT SPEAKER OUTPUT PX-1000.4 2-30A It is critical to use the proper Using spade terminals, connect the PX-2000.1D 2-40A power and ground cable.

This manual is also suitable for:

Px-1000.4Px-2000.1d