Summary of Contents for Aqua One Styleline 122
- Page 1 Assembly Instructions Please keep for future reference Styleline 122 Version 1 : 01/08/2017 Important - Please read these instructions fully before starting assembly ALR3417...
-
Page 2: Care And Maintenance
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit is heavy. • Make sure you have enough • We do not Please lift with care. space to layout the parts before recommend the starting. - Page 3 Panels Please check you have all the panels listed below 1 Left Side 2 Right Side 3 Left Divider 4 Right Divider (DF-00012353) (DF-00012354) (DF-00012368) (DF-00012384) (71.8 x 31.8cm) (71.8 x 31.8cm) (71.8 x 29.8cm) (71.8 x 29.8cm) 5 Top (DF-00012361) (122.5 x 37.2cm) 6 Base...
- Page 4 Fittings Please check you have all the fittings listed below Large Locking Cam Large Metal Dowel x 12 Wooden Dowel x 20 (F901) (F22) x 12 (F900) 45mm Screw 40mm Screw (F65) (F910) 38mm Screw x 12 (F81) Hinge Plate 13mm Screw x 12 (F63)
- Page 5 Step 1 10mm Prepare the Left Side Tap 4 Wooden Dowels into the Left Side. Insert 2 Large Locking Finished Cam Nuts into the Left Front Edge Side. Screw a metal dowel into the Left Side. Fit 2 hinge plates onto the Left Side, making sure that the slot is facing towards the...
- Page 6 Step 4 Fit the Sides to the Front Rail Push the Sides onto the Front Rail. Use a screwdriver to tighten the 2 Large Locking Cam Nuts fitted to the Front Rail. Note: Turn the Large Locking Cam Nuts as far Finished Finished as they will go - more...
- Page 7 Step 6 Only fit Hinges to the Left Divider if you want the middle door Prepare the Left Divider to open this way If required, fit 2 Hinge Plates onto the Left Divider, making sure that the slot is facing towards the finished front edge.
- Page 8 The rest of the stages will show Step 8 the Hinge Plates on the Right Divider. You may have chosen to Fit the Dividers fit them on the Left Divider. Push the Dividers onto the Base and fix them using four 40mm screws. Step 9 Packaging piece...
- Page 9 Step 11 Fit the Top Push the Top onto the assembly. Use a screwdriver to tighten the 8 Large Locking Cam Nuts fitted to the Sides and Dividers. Make sure that the Shelf Support fitted to the Front Rail is pushed into its hole in the Top.
- Page 10 Step 14 Fit the 6 Feet Fit the 6 Feet to the Base using the 38mm Screws. Step 15 Prepare the 3 Doors Push fit 2 Hinges into each of the Doors. Secure each Hinge with two 13mm screws into the shallow mark holes.
- Page 11 Step 16 This unit must be fixed to a wall using the Secure the unit to a 2 Overbalance Protector Kits provided wall Before fitting the unit to a wall, use a spirit level to check the top of the unit is level, front-to-back and side-to-side in the 3 positions shown.
- Page 12 Step 17 Fit the 3 Doors The easiest way to attach each Door is to fit the top Hinge first, then align and fit the other Hinge. Push the Hinge onto the front part of the Hinge Plate. The recess at the bottom of Screw B goes into the slot in the Hinge Plate.
- Page 13 Step 18 Adjust the Doors if needed Before adjusting the Doors, use a spirit level to check the Base (or Top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the...