Subscribe to Our Youtube Channel
Related Manuals for Presenza QK032
Summary of Contents for Presenza QK032
- Page 1 STAINLESS STEEL WORKCENTER SINK INSTALLATION GUIDE AND USER MANUAL Model No. QK032...
-
Page 2: Table Of Contents
Table of Contents Topmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Table of Contents . -
Page 3: Warranty
Warranty ONE-YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported . We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation . Conglom Kitchen &... -
Page 4: Pre-Installation
Pre-Installation PLANNING INSTALLATION Inspect your unit before proceeding. Check the surface for any flaws or damage, including dents, bends, bumps, or scuff marks. If any damage is noticed, do not proceed with installation . Please return the unit to place of purchase for an exchange . If there are any missing parts, please contact the manufacturer for replacements . -
Page 5: Package Contents
Pre-Installation (continued) PACKAGE CONTENTS Part Description Quantity Stainless steel sink Bottom grid Sliding sink Colander Bamboo cutting board Vanishing edge strainer Strainer assembly Topmount clips Undermount clips CONGLOMKB .COM Please contact customer .service@conglomkb .com or 1-877-333-0098 for further assistance . -
Page 6: Installation
Installation UNDERMOUNT INSTALLATION CREATING THE TEMPLATE CUTTING THE COUNTER NOTE: CAUTION: Always wear safety goggles and gloves when Undermount sinks are mounted from below the counter. If you using power tools to prevent personal injury . are installing a topmount or “drop-in” sink, please see “topmount installation”... - Page 7 Installation (continued) DRILLING THE HOLES FOR THE UNDERMOUNT CLIPS CAUTION: Always wear safety goggles and gloves when using power tools to prevent personal injury . - On the underside of the counter, mark the location of the ten holes (5) for the undermount clips (J) . These holes should be equally spaced around the perimeter of the cut- out with three on each side 2 and 4 and two on each side 1 and 3 .
- Page 8 Installation (continued) INSTALLING THE SINK NOTE: Install the faucet according to the manufacturers instructions before this step. Install the vanishing edge strainer according to the instructions before completing this step. See page 11. - Put the threaded inserts on the bolts of the undermount clips (J) loosely in the holes that you drilled for them in the underside of the counter .
-
Page 9: Topmount
Installation (continued) TOPMOUNT INSTALLATION CREATING THE TEMPLATE CUTTING THE COUNTER NOTE: CAUTION: Always wear safety goggles and gloves when Topmount sinks are dropped into the counter from above. If you are using power tools to prevent personal injury . installing an undermount sink, please see “undermount installation” on page 6. - Page 10 Installation (continued) INSTALLING THE SINK NOTE: Install the faucet according to the manufacturers instructions before this step. Install the vanishing edge strainer according to the instructions before completing this step. See page 11. - Apply silicone sealant (not included) around the underside of the lip of the sink (A) on all four sides . - Carefully lower the sink (A) into the counter, ensuring that the factory installed topmount clips (H) do not catch on the counter edges .
-
Page 11: Installing The Vanishing Edge
Installation (continued) INSTALLING THE VANISHING EDGE STRAINER NOTE: If you are installing a garbage disposer (not supplied), do not install the strainer. You will need to purchase from Conglom Kitchen & Bath, an adaptor. This will replace the flange from your garbage disposer. Install the garbage disposer according to the manufacturer’s installation instructions replacing the flange for the adaptor. -
Page 12: Operation
Operation USING THE SLIDING SINK AND COLANDER - The sliding sink (C) and the colander (D) can be placed in any location along the track (1) in the sink (A) . - The colander (D) fits inside the sliding sink (C) for easy storage . -
Page 13: Care And Cleaning
Care and Cleaning SINK, SLIDING SINK AND COLANDER Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care . Do Not - After use, always rinse your sink with tap water to - Do not allow any food, detergent, soap or grease dilute and remove deposits . -
Page 14: Service Parts
Service Parts If you are missing parts or if you require replacement parts, please call our customer service team at customer .service@conglomkb .com or 1-877-333-0098, 8:30 am - 5 pm, EST Monday - Friday . Identify the required part(s) and have the part number(s) ready . Part Description Code Quantity... - Page 15 Imported by: St-Laurent, Québec, H4S 2C3 1-877-333-0098 customer.service@conglomkb.com www.conglomkb.com Made in China Retain this manual for future use.
Need help?
Do you have a question about the QK032 and is the answer not in the manual?
Questions and answers