Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Artec Mini Tracker 506
- Page 1 Mini Tracker 506 User Manual...
-
Page 2: Care And Maintenance
Care and Maintenance Warning Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. Do not use or store the device in dusty, dirty areas. - Page 3 Care and Maintenance The working range, alarm range, searching and detection are depends the terrain environment because of radio wave efficiency. If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder alarm sound.
- Page 4 Overview Master Back Front Left direction Hanging hole for Distance indication strap Signal indication Power on (Standby) Power off Search button (Sleeping) LED light button (Mute distance Battery cover melody button at search mode) Slave Front Back Hanging hole for strap Signal indication...
-
Page 5: Working Method
Working Method Master Slave Slave Alarm 8~16 m Alarm Search 100 m Specification Master Slave 23x46x8 mm 19x28x7.5 mm Size Frequency 2.4GHz ISM 2.4GHz ISM LR 1130 × 2 LR 1 130 × 2 Battery Switch ON / OFF 2 buttons Button 8~16m Sleeping... - Page 6 The Battery Installment Master 1. Press the clip on battery cover then push backwardly. 2. Put 2pcs batteries into. *** Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on battery cover.
-
Page 7: Getting Started
Getting Started For the first time use, please set the battery into Master according to above battery installment . Pull out Plastic isolation Place two devices no Switch to power on more than 10 cm apart. Beep Beep Caution Beep Distance indication Signal indication... - Page 8 Search Near 1.) LED light: more closer, more lights. 2.) Search melody: more closer, more rapid. Press Search button Start to detect the location 2~3 seconds of Slave.
- Page 9 Search North Turn to different directions for signal comparison 2 Distance LEDs Go the way of the strongest signal direction to find out Slave. One Distance LED only 3 Distance LEDs. East The strongest signal direction ! West 2 Distance LEDs South...
- Page 10 Search Mute searching melody from Master. Listen beep sound from Slave to assist short range searching. Beep Press & hold the LED Stop the melody Listen to the beep light button and light up the sound from Slave torch LED...
- Page 11 Search Signal indication Back to Standby mode Stop searching Signal LED flashes every second for re-linking Press Search button 2~3 seconds Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance. 1.) Search from correct direction to wrong direction 2.) Over pass...
- Page 12 Searching Example Location: North North Signal indication East 0 ～ 100 m Go to the wrong direction Distance LED goes out all lights suddenly and only flash Original searching Signal LED with beep sound (Right direction) North East 3 seconds Suggestion later LED displays new...
- Page 13 Alarm Beep Beep Signal indication Over 8~16 meter. Stop alarm (beep) if both devices comes within 8 meter again. Come with beep! When Slave and Master are over 100 Caution meter or lose signal Slave flashes half minute to No linking then into sleeping wait for re-linking modeand stop flash...
- Page 14 Sleeping Switch to sleeping mode Switch the button to section 0 (OFF) Under Standby mode Stop signal to Slave Slave flashes half minute to wait for re-linking No linking then into sleeping mode and stop flash...
- Page 15 Re-link / Wake up Beep Beep Distance indication Switch the button to Signal LED ON for re-linking Re-link successful! section 1 (ON) Available for distance within Master shows the distance 100 meter between Slave via LED and melody (beep) Beep Can't get signal from Slave.
-
Page 16: Low Battery
Low Battery 1 beep sound every 20 seconds continuously. If this kit is under low battery stage, it may cause abnormal display to alarm, beeps or non-working to confuse actual working stage. Please change new battery as soon as possible. - Page 17 Suggested setting place スターター Correct Wrong holding holding *** Do not cover the top side of Master.
- Page 18 Suggested setting place Master Slave...
- Page 19 91E-02B2-U50G10...
Need help?
Do you have a question about the Mini Tracker 506 and is the answer not in the manual?
Questions and answers