Advertisement
do noT insert foreign objects or material into the hole reserved for the battery.
8
do noT force the battery into the charger. the battery will only fit one way to ensure correct polarity alignment.
8
do noT charge a second battery immediately. consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes
8
before charging the next battery.
store the charger in the same manner as the battery, see section 1.2.
9
1.3.
General SafeTy.
maintain the drill and battery in good condition. check moving parts alignment on a regular basis.
9
replace or repair damaged parts. use an authorised service agent and recommended parts only. unauthorised parts may be
9
dangerous and will invalidate the warranty.
ensure the drill is switched off before installing the battery pack.
9
Keep the drill and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the drill; e.g. ceilings, floors and enclosures may contain electrical items or water piping
9
ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
9
secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this drill does not need to be plugged into the mains power.
9
Keep chuck direction switch in the locked position until the drill is required for use.
9
Keep children and unauthorised persons away from the working area.
9
do noT use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
do noT allow children to operate the drill.
8
do noT operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
do noT hold unsecured work piece in your hand.
8
do noT leave the drill operating unattended.
8
do noT carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
8
do noT use the drill for a task it is not designed to perform.
8
do noT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do noT get the drill or battery charger wet or use in damp or wet locations.
8
2. inTroduCTion
compact, lightweight cordless drill/driver with added hammer function. comfortable composite housing with soft grip to reduce vibration.
the drill has 0.8-10mm keyless chuck. With 2 speed settings and 21 torque settings gives control to complete various tasks.
integral led battery level indicator and led work light. complete with belt hook for safer storage while not in use. requires model
no.cP1200BP 12V 1.5Ah lithium-ion battery and model no. cP1200mc battery charger.
3. SPeCifiCaTion
model no.. ................................................................. cP1201
Battery .................................. 12V 1.5Ah li-ion (not included)
no load speed ...........................................0-400/0-1300rpm
impact rate ............................................ 0-6000/0-19500bpm
noise power: ................................................................94dBA
noise pressure: ............................................................84dBA
drilling capacities
Wood ............................................................................ 20mm
metal ............................................................................ 10mm
concrete ...................................................................... 10mm
chuck size ................................................................... 10mm
maximum torque ...........................................................25nm
Battery model no ..................................................cP1200BP
mains charger model no .....................................cP1200mc
Weight ......................................................................... 0.85kg
4. CHarGinG
battery Pack removal and replacement
4.1.
4.1.1.
switch the machine off before removing the battery pack.
4.1.2.
Press the battery latches in (located either side of grip
and withdraw the battery pack (fig.1).
4.1.3.
to replace the battery pack, push the stem into the drill
until the latches engage. the battery pack can only be
inserted in the correct orientation.
4.2.
battery Charging
4.2.1.
Batteries that have been out of use for some time or are new
may not accept a full charge. this is not a battery fault; the
battery may need to be discharged and charged a couple of
times to restore full capacity.
4.2.2.
Connect the charger to the electric power supply. A flashing
green led will show.
4.2.3.
insert the battery into the charger. A steady red light
will show.
4.2.4.
When fully charged, a steady green led will show.
4.2.5.
the battery is ready for use.
4.2.6.
© Jack sealey limited
fig.1
Original Language Version
cP1201 | issue2(sP) 30/08/17
Advertisement
