Boss Audio Systems BRRC14 User Manual

USER'S MANUAL
BRRC14
RECOIL SERIES
BLUETOOTH ® | 14" AMPLIFIED SOUNDBAR SYSTEM
QUICK START GUIDE
USER'S MANUAL
BRRC14
RECOIL SERIES
14" AMPLIFIED SOUNDBAR SOUND SYSTEM
WITH BLUETOOTH REMOTE CONTROLLER
BOSS Audio Systems
www.bossaudio.com
Tech Support: www.bossaudio.com/support/technical-support
iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries
Android is a trademarks of Google Inc. registered in the U.S. and other countries.
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including
photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.
Copyright © 2017 BOSS AUDIO Inc.
317 VER:1.1 EN
Thank you for purchasing this
BRRC14 Soundbar Sound System
Please read through these instructions carefully so you will know
how to operate your model properly.
in a safe place for future reference.
THIS PACKAGE CONTAINS
1 - BRRC14 Soundbar Speaker System
1 - Bluetooth Multi-Function Controller Kit
1 - 1.50" Rollbar Mounting Kit
1 - 1.75" / 2.00" Rollbar Mounting Kit
1 - Quick Connect Power Cable
1 - User Manual Quick Start Guide / Poster
1 - Warranty Card / Facebook Card
INFORMATION TO THE USER
T he Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
BLUETOOTH OPERATION
3
6
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
3
1) Power on the MFC by long-pressing the Power button for 3 seconds, long-press the
6
Bluetooth button for 3 seconds, the BLUE LED
the MFC is now ready for Bluetooth pairing
NOTE: You have 2 minutes before you must restart this procedure over again.
2) The MFC is now in pairing mode:
ANDROID users:
a. Go into the Settings Menu of your device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth and press SCAN
d. "BOSS REBEL UTV" will now be displayed under AVAILABLE DEVICES
e. If prompted, enter passcode: "0000"
iOS users:
a. Go into the Settings Menu of your iOS device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth
d. "BOSS REBEL UTV" will now be displayed
e. If prompted, enter passcode: "0000"
3) If BOSS REBEL UTV is not seen, repeat the above steps to refresh the "Device List"
4) When the connection is successful a tone will be heard, and the Bluetooth LED indicator
will light solid, you are now ready to stream music from your favorite media player to the MFC
BEFORE YOU START INSTALLATION
To avoid potential shorts in the electrical
battery cable before installation. Use this
grounding only. Failure to do so may result
this product. To avoid short-circuiting, cover any disconnected leads with insulating
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground, make sure
to metal parts of the vehicles body frame or direct to the battery if your vehicle
does not have a grounded chassis frame The ground wire of this units power amp
and a second powered system must be connected to the frame separately with
ONBOARD CONTROL PANEL
MUTE - ON/OFF STATUS INDICATOR LED DOME - ON/OFF
WHITE = ON
RED = STANDBY
NOTE!!
PRINTED IN CHINA 10 minutes when MFC ACC is turned OFF
INFORMATION TO THE USER
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person's body (excluding extremities: hands, wrists, feet and ankles). Alteration
user's right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
USER MANUAL
does cause harmful interference to radio or television reception, which can be
QUICK START GUIDE
correct the interference by one or more of the following measures:
receiver is connected.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
BLUETOOTH OPERATION
RECONNECTION
1) Power on the MFC and your last paired device Bluetooth.
2) Ensure you are within range of the MFC, the unit will now automatically reconnect
3) If the device is out of range from the MFC, it will disconnect automatically:
a. The MFC will reconnect automatically to your device when in range
4) If your device was previously paired with the MFC, but it wasn't the last paired device:
a. Ensure no other devices are currently paired
b. Enter the Bluetooth Menu on your device being paired
c. "BOSS REBEL UTV" will display under AVAILABLE DEVICES
d. Choose the "BOSS REBEL UTV" to reconnect
5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth
button for 10 seconds
NOTE: Some devices may require a manual Bluetooth reconnection once the devices
Bluetooth is powered OFF / ON and/or back in range, repress the BOSS REBEL UTV
button in BLUETOOTH settings on your device
Using this product without running the engine can drain the battery.
Tips:
To avoid battery exhaustion, be sure to occasionally run the
vehicles engine while using this product.
MOUNTING THE SOUNDBAR
Rubber Bushing
Your Rollbar
Rubber Bushing
T-nut must be assembled
3mm Allen Head
INSTALLATION PARTS
RUBBER BUSHINGS BRACKETS
1.5"
1.5"
Some applications may require
Align notch
optional friction tape between
rubber bushings for a secure,
1.75"
most local hardware stores
1.75" or 2"
Align notch
2"
1) Determine the size rollbar for your vehicle, install rubber bushings on rollbar
2) Insert and align notch of rubber bushings into the aluminum brackets
3) Apply supplied Loc-Tight to allen bolt tips, let dry for 20 minutes, then align
the allen bolts and T-nuts into the T-channel
4) Recheck all allen bolts are tight, ensure T-nut's are properly seated in the
T-channel correctly
CAUTION!!
Mounting brackets should be periodically checked to be sure they are tight
and secure before use of the vehicle.
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
safety consideration of others should always be your highest priority
In the event you should notice smoke, strange noises or odor from this product, or any
BOSS AUDIO Service Center. Using this product in this condition may result in
permanent damage to the system
Set your volume control at a low setting, then slowly increase the sound until you can
hear it comfortably without distortion, or ear discomfort
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES: USB 1A
- Do not turn up the volume so high that you can't hear what's around you
CHARGING
NOT FOR AUDIO PLAYBACK
INSTALLATION PRECAUTIONS
WARNING - Always consult a professional installer
Do not attempt to install or service this product by yourself. Installation or servicing of this
product by persons without professional training and experience in electronic equipment
BOSS AUDIO SYSTEMS Service Center
The BRRC14 should be hard wired directly to the main vehicle battery
When wiring directly to the vehicles battery, be sure to disconnect the batteries negative
terminal wire before starting any wiring procedures
The ground cable length should be short as possible (See wiring diagram)
The BRRC14 has a weather resistant design, it should not be under any circumstances
submerged in, or under water
Use only the supplied installation parts provided with the BRRC14
Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth
Rinse well with clean water
"DO NOT'S" - Very Important
DON'T clean in hot sun or on very hot days
DON'T use abrasive or highly alkaline cleaners on the main body
DON'T ever use, gasoline, acetone or carbon tetrachloride
DON'T ever use a pressure washer aimed at the speakers
CAUTION!! Using other mounting methods may void this warranty
STREAMING MUSIC
4
9
5
8
7
MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
5
1) Press the PLAY/PAUSE once to start playing music or press the PLAY button from
MULTIFUNCTION CONTROLLER AUX-IN OPERATION
your devices touch screen
4
2) To skip songs or advance, press the NEXT TRACK button
1) Power on the MFC by pressing and holding down the
7
3) To select the previous song, press the PREVIOUS TRACK button
2) Disconnect any paired Bluetooth
Settings Menu
3) Connect your 3.5mm AUX-IN cable located on front side of the MFC to your devices
headphone jack
VOLUME CONTROL
4) Route the wire back to MFC, secure your device in a safe location
9
4) To raise the volume press the VOLUME UP button or use your devices controls
VOLUME CONTROL
8
5) To lower the volume press the VOLUME DOWN button or use your devices controls
5) To raise the volume press the
NOTE: If BLUETOOTH or AUX is disconnected for more than 10 minutes the MFC will
automatically turn OFF, however, when not in use the ACC switch should be manually 6) To lower the volume press the
turned OFF to keep the vehicles main battery from draining
7) To MUTE the volume press the
Make sure your device Bluetooth volume is set at 100% level
Tips:
before stowing your device
MULTI-FUNCTION CONTROLLER MOUNTING
OPTIONAL
OPTIONAL
o
MFC can rotate 90 for the
best mounting position
ROLLBAR / CAGE MOUNT
1.5" 1.75" 2.00"
3mm Allen Head
FLUSH MOUNT
1) Always check mounting depth before cutting
BLUETOOTH
6) Insert MFC
SURFACE MOUNT
1) Check mounting depth before drilling
SPEAKERS
AMPLIFIER
screw in place
5) Insert MFC
GENERAL
TOOLS NEEDED: OPTIONAL TOOLS NEEDED:
- Crimp Tool - Hand saw or Jigsaw
- Wrench or Pliers
- 3mm Allen Wrench
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
GETTING STARTED
GETTING TO KNOW YOUR
BRRC14 MULTIFUNCTION CONTROLLER (MFC)
2 3
A 1
MFC RESET
4
LONG PRESS BOSS
LOGO FOR 10 SECONDS
9
5
6
8 7
ALWAYS CLOSE COVER WHEN
OPEN 3.5mm AUX-INPUT
NOT IN USE NEVER USE WHEN
IN MUD and/or WATER CABLE NOT INCLUDED
A MFC - MULTIFUNCTION CONTROLLER
1 DOME LIGHT ON/OFF -
(Auto 10 minute timer when MFC ACC is turned OFF)
2 POWER ON/OFF - Press and hold for 3 seconds
3
LOUDNESS ON/OFF - Single Press
4 NEXT TRACK -
FF press and hold
5
PLAY/PAUSE - AUX MUTE
6
BLUETOOTH PAIRING INDICATOR LED - BLUE / AUX RED COLOR
7
PREVIOUS TRACK -
FR press and hold
8
VOLUME DOWN - Ramp DOWN press and hold
9
VOLUME UP - Ramp UP press and hold
AUX-INPUT
3
YOUR
9
DEVICE
5
Close USB cover
when not in use
CAUTION!!
Never use USB
8
or AUX while in
mud and/or water
INSERT
MFC can play audio from
(Cable not included)
any device that has a 3.5mm
headphone audio jack.
3
POWER button for 3 seconds
Bluetooth in your devices
9
VOLUME UP button
8
VOLUME DOWN button
5
PLAY/PAUSE button
Make sure your device headphone volume is set at 100% level
Tips:
before stowing your device
WIRE DIAGRAM
ALIGN CONNECTOR
PINS, INSERT and
HAND TIGHTEN
CAUTION:
NEVER CONNECT THE MFC DIRECTLY
TO THE BATTERY, ALWAYS USE AN
ACCESSORY SWITCH
ACC SWITCH
MFC
RED
NEVER CONNECT +12V
TO THE DOME WIRE
BLACK
GROUND CRIMP (-) MOMENTARY TO ACTIVATE
(-) ORANGE DOME LIGHT
(+) BLUE AMP REMOTE INPUT
INSERT
RIGHT
INSERT
( AUX Cable not included) LINE IN
LINE OUT
BOSS REFLEX SERIES
OPTIONAL SYSTEM
LEFT
EXPANSIBILITY
DAISY CHAIN
LINE OUTPUTS
DIRECT BATTERY WIRING CIRCUIT
15A
RED
Fuse and fuse holder
BLACK
BATTERY Replace with 15A only Ground wire
Chassis
Chassis
ground
ground
point
point
Metal frame
SPECIFICATIONS
Dimensions:
14.02" (356mm) x 4.98" (126.5mm) x 5.55" (141mm)
Weight:
9.92 lbs (4.5 kg)
5.55"
(141mm)
14.02" 4.98"
(356mm) (126.5mm)
o F to 175 o F / -15 o o C
o F to 140 o F / 0 o C to 60 o C