Advertisement
Quick Links
Operating
M anual
-‐-‐CN90B
I ndustrial
C oil
N ailer-‐-‐
NOTE: Please read and fully understand the instructions in this
manual
b efore operating the pneumatic power tool. Carefully read
through
t his OPERATOR'S MANUAL to ensure efficient, safe
operation. It is
r ecommended that the Manual be kept readily available
as an important
r eference when using this tool.
Advertisement
Related Manuals for Orion CN90B
Summary of Contents for Orion CN90B
- Page 1 Operating M anual -‐-‐CN90B I ndustrial C oil N ailer-‐-‐ NOTE: Please read and fully understand the instructions in this manual b efore operating the pneumatic power tool. Carefully read through ...
- Page 2 IMPORTANT INFORMATION WARNING: The warnings, cautions and instructions d iscussed in this instruction manual cannot cover all p ossible conditions and situations that may occur. It must be u nderstood by the operator that common sense and caution a re factors which cannot be built into this product, but must ...
- Page 3 WARNING: The operating instructions shall draw attention to the following a) Only those fasteners listed in the operating instructions may be used in the fastener driving tools; NOTE: The fastener driving tool and the fasteners listed in the operating instructions must be seen as one unit system in terms of technical safety.
-
Page 4: Safety Information
SAFETY INFORMATION WARNING: BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND T HE FOLLOWING SAFETY INSTRUCTIONS.FAILURE TO FOLLOW W ARNING COULD RESULT IN DEATH OR SERIOUS INJURY. 1. WEAR SAFETY GLASSES OR GOGGLES. ... - Page 5 6. DO NOT USE A WRONG FITTING. The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the line of air is disconnected, possibly causing injury.
- Page 6 14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK AND THIN MATERIAL The work piece is likely to split and the fastener could fly and hit someone. 15. DO NOT DRIVE FASTENERS ON THE TOP OF OTHER FASTENERS. Driving fasteners of the top of other fasteners may cause deflection fasteners which could cause injury.
-
Page 7: Technical Data
TECHNICAL DATA Type of tool CN90B Industrial Coil Nailer 14-1/4”X12-3/8”X5-5/8” Dimensions 360mmX312mmX141mm Weight (without fasteners) 3.50kgs (7.70lbs.) Magnesium body Actuation mode Contact actuation Magazine capacity 200-300 nails Maximum allowable pressure 120psi (8.3bar) Recommended pressure range 70psi to 100psi (5bar to 7bar) Fasteners Only the nail sizes shown in the table below can be driven with this nailer. - Page 8 NAILER CONNECTION AND OPERATION NOTE: The information contained in this manual is designed to assist you in the safe operation of the nailer. Some illustrations in this Manual may show details or attachments that are different from those on your nailer. Air Supply, Connections and Operating Pressure Read section titled SAFETY.
- Page 9 Nailer Connection and Operation Lubricator • The lubricator supplies and oil mist to the nailer. • Inspect the lubricator before operation to be sure the supply of lubricant is adequate. • If an inline lubricator is not used, a few drops of oil will need to be added to the nailer inlet before each use.
-
Page 10: Instruction For Operation
INSTRUCTION FOR OPERATION 1. Before operation (1) Wear safety glasses or goggles (2) Do not connect the air supply (3) Inspect screw tightness (4) Check operation of the contact arm & trigger if moving smoothly (5) Connect the air supply (6) Check the air-leakage.(the tool must not have the air-leakage.) (7) Hold the tool with finger-off the trigger, then push the contact arm against the work- pieces.(the tool must not operate.) -
Page 11: Maintenance And Inspection
MAINTENANCE AND INSPECTION Read the section title SAFETY. SERVICE AND REPAIRES All quality tools will eventually require servicing or replacement of parts due to wear from normal use. It is recommended that these operations should be performed by a professional technician. - Page 12 PARTS LIST-CN90B CN90B SPARE PARTS LIST CODE DESCRIPTION CODE DESCRIPTION 610280 BOLT M8X20 620050 TRIGGER VALVE SPRING 320480 EXHAUST COVER 510240 O-RING 8.6X1.9 630070 SPRING WASHER 510210 O-RING 6.3X1.8 610230 BOLT M6X30 330010 TRIGGER VALVE BUSHING 324750 SIDE PROTECTOR 510180 O-RING 5.8X1.9...
- Page 13 TOOL SCHEMATIC-CN90B ...
- Page 14 CN90B Industrial Coil Nailer---1511 ...
Need help?
Do you have a question about the CN90B and is the answer not in the manual?
Questions and answers