1. Manuals
  2. Brands
  3. LAMI Manuals
  4. Laminators
  5. Daisy-55EC
  6. Instruction manual

LAMI Daisy-55EC Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Summary of Contents for LAMI Daisy-55EC

  • Page 2 Foot Switch Installation Method......................P 6 Power Connection for re-winding Device (Optional)................P 6 Fuse Installation Method ........................P 7 Name of Each Part Main Body of DAISY-55EC ......................P 8 Operation Panel............................. P 9 Foot Switch............................P 10 Before Processing Laminate P 11 About Laminate Film ..........................

  • Page 3: Precautions Before Use

    Precautions Before Use This document uses symbols to explain the degree of harm and damage caused by incorrect use of the product and to prevent harm on customers and others or damage on properties. If this symbol is neglected and the product is handled incorrectly, serious injury or death may Warning occur.
  • Page 4 Warning Power cable included in the product must be used. Do not use power supply not indicated on the product. Do not place heavy objects on power cable, place cables nearby heating devices, or complex wiring. Do not process power cable or use damaged power cable. Accurately insert to the end of electrode.
  • Page 5 This device shall be installed in the following places. Horizontal and stable place Use as slanted or in unstable state may result in adverse effects such as paper return. Also, unexpected accidents can occur. Place where exclusive power outlet is available Do not use power types other than the rated voltage regulated on this Manual.
  • Page 8 Fuse is placed nearby the power switch on the rear of right surface and power switch of the Re-winding device (optional). (Spare fuse is only included in the Re-winding device.) Take out the fuse using flat-head driver to check disconnection of the fuse. If it is disconnected, replace with a new fuse before supplying power again.

  • Page 9: Name Of Each Part

    Name of Each Part Stand Reserve film shaft Media holder shaft Film shaft for under-film Idle roller (front) Front signboard Finger jamming prevention cover Laminate roll Stay bar (reinforcement bar) Film shaft for release paper Laminate film shaft Idle roller (top) Back signboard Winding film shaft are optional.

  • Page 10: Lcd Display Panel

    LCD Display Panel Speed Forward and reverse rotation of roller Current status Displayed during laminate processing STOP Displayed when laminate processing is stopped FORWARD If FORWARD is shown on the LCD panel, the roller rotates in forward direction. REVERSE If REVERSE is shown on the LCD panel, the roller rotates in reverse direction. EMEGENCY When emergency stop button is pressed, EMERGENCY pops up on the LCD panel.
  • Page 11 Buttons on the operating panel button TEMPERATURE button This button is not used. This button is not used. SPEED button THICKNESS button This button is not used. Rotational speed of the laminate roller can be adjusted within 0 ~ 3.0 m/min. MEMORY button PRESS/RELEASE button This button is not used.
  • Page 12 Before Processing Laminate There are two types of laminate film including roll type pack type . This product uses cold roll film type. Pack type and hot roll film cannot be used. Thickness of the laminate film is selected according to the use. Thickness ( ) Thickness of the cold roll film used by this product ranges from 20 to 300 .
  • Page 13 Cold Laminate Processing 1 Install the paper tube holder on the film shaft. All 6 film shafts are common parts. Use hex wrench to move or fixate the branch pipe holder. Fixate 4 sides of each branch pipe holder. 2 Install the under-film. Refer to the figure below to pass the under-film while laminate roller (top) is lifted.
  • Page 14 Only cut the release paper on the laminate film and rotate the laminate roller until the cross section of the release paper cut touches the re- winding paper tube. Here, hold the release paper so that it does not get entangled. When the release paper touches the re-winding paper tube, attach it using cellophane tape to finish installation.
  • Page 15 Release paper Paper tube for re-winding release paper Laminate film Under-film Paper tube for product Re-winding 5 Perform laminate processing. 1 : Use the handle to adjust pressure (gap) according to thickness of processing material. 2 : Adjust to the wanted speed using SPEED button (speed can be adjusted during rotation of the laminate roller) and press RUN/STOP button to rotate the laminate roller.

  • Page 16: Maintenance

    Maintenance This product is composed of many rollers, and they must be cleaned according to usage. The laminate can be maintained in desirable state by cleaning the rollers. Clean each roller since rollers have paper scraps and dusts attached. The roller must be stopped when cleaning. Do not clean the roller using hard objects such as steel wool.

  • Page 17: Troubleshooting

    Troubleshooting The following measures are taken for troubleshooting. Insert outlet plug and check power switch This product is used at 240V . Make sure that the outlet plug is correctly connected. Check that the power switch on the back of the main body is turned on. If power cable is disconnected, it must be replaced.

Table of Contents