Advertisement
Advertisement
Related Manuals for RotoSpa quatrospa
Summary of Contents for RotoSpa quatrospa
-
Page 3: Table Of Contents
Contents Introduction………………………………………………………………………1 Electrical Supply………………………………………………………………..2 Getting Started Step by Step guide…………………………….… 3, 4 Using your RotoSpa’s control panel and it’s functions…..…..5 Maintenance……………………………………………………………….6,7,8 QuattroSpa Specifications…..…………………………………………..9 Health and Safety…………………………………………………………...10 Troubleshooting………..………………………………………………11, 12... -
Page 5: Introduction
This guide will explain everything you need to know about the set up and continual use of your RotoSpa. In order to obtain maximum benefit from your RotoSpa we recommend that you read and follow the information contained in this guide. -
Page 6: Electrical Supply
The circuit must be RCD protected having characteristics specified in regulation 415.1.1 of the IET wiring regulations. The RotoSpa will be supplied with a 3 meter 3 core flex cable with a male commando plug attached. Please note if your socket is positioned too far away from the RotoSpa the cable may not reach. -
Page 7: Getting Started Step By Step Guide
To increase the Ph., add 8 grams of Ph. + to some water in a plastic container and mix, slowly add the solution to your RotoSpa. Ensure the jets are on so the ph.+ solution is evenly distributed through the entire volume of water. After 5 minutes turn the jets off and use the test strips or the Scuba digital tester to check the ph. - Page 8 For Bromine users add 3 grams of non-chlorine shock to a plastic container with a sample of your spa water, mix well and add to your RotoSpa, allow jets to run for a few minutes so solution can distribute evenly. It is advised that you run your Bromine level at 8ppm to completely eliminate and contaminants within your water (allow to drop to 4-6ppm before using your RotoSpa).
-
Page 9: Using Your Rotospa's Control Panel And It's Functions
Green Light To turn the blower off you will need to push the air button a fourth time. Air diverter- This is a feature sited only on the QuatroSpa. This dial will divert the flow of water from one side of the hot tub to the other, or, if moved to the centre will evenly distribute the flow... -
Page 10: Maintenance
RotoSpa’s recommended maintenance tips in order to keep you safe and to keep your tub of top condition. We advise an annual service of your RotoSpa by one of our engineers to keep your QuattroSpa in as new condition and to check for any wear and tear of components and/or pipework. - Page 11 If kept clean and well balanced your water can last up to 4 months before needing to be changed. To drain the water, you will need to attach a hose to the drain valve, this is located on the bottom edge of the RotoSpa (see page 8), you will then need to place the end of the hose in the area you wish the water to drain to.
- Page 12 Servicing your hot tub As previously mentioned annual servicing of your RotoSpa will reduce the risk of breakdowns and unnecessary costs for emergency call outs. We have a few differing service packages available depending on your needs. They range from winter shutdown to a full inspection of pipework, glue joints, performance ratings on your pump, heater and control box.
-
Page 13: Quattrospa Specifications
QuattroSpa Please see below for a diagram of your hot tub’s specifications Hydro Jets Suction Cover Air Blower Jets Not fitted as standard- optional extra Bathers seating Bench Water Diverter Drain Valve. Non slip Located in the texturized hand hold at Entry/Exit Step the foot of the hot tub. -
Page 14: Health And Safety
Health and Safety Hot Tubs can be a very enjoyable way to spend time and make memories with friends and family when used in a responsible manner. Please read through these health and safety notes to ensure you and your guests are kept safe. -
Page 15: Troubleshooting
Troubleshooting Please see below for possible problems that may occur during your ownership of a RotoSpa Hot Tub. For anything not listed please revert to your touchpad user guide supplied with your Hot Tub or call our office for further assistance. - Page 16 Pump has become Laboured/Noisier There may be a fault with the pump or Check that the water levels are correct than normal there is not enough water in the hot (see page8) tub. Have you recently moved the location of the hot tub? The pump on our Hot Tubs can appear noisier if the tub itself is enclosed (in a cabin/log house) or when...
Need help?
Do you have a question about the quatrospa and is the answer not in the manual?
Questions and answers