Stopping The Engine; Ac Operation; Eco Throttle System - Honda EG2800i Owner's Manual

7. If the choke rod was moved
to the CLOSED position to
start the engine, gradually
push it to the OPEN position
as the engine warms up.
8. If you wish to use the Eco
Throttle system, turn the Eco
Throttle system switch to the
ON position after the engine
has warmed up for 2 or 3 minutes.

Stopping the Engine

To stop the engine in an emergency, simply turn the engine switch to
the OFF position. Under normal conditions, use the following
procedure.
1. Turn off or disconnect all appliances that are connected to the
generator.
2. Turn the engine switch to the
OFF position.
3. Turn the fuel valve lever to
the OFF position.

AC Operation

Before connecting an appliance(s) to the generator, make sure that it
is in good working order and that the appliance(s) total electrical rating
does not exceed that of the generator.
Most motorized appliances require more than their electrical rating for
startup. When an electric motor is started, the overload alarm (red)
may come on. This is normal if the overload alarm (red) goes off
within nine seconds. If the overload alarm (red) stays on, consult your
generator dealer.
NOTICE
Substantial overloading may damage the generator. Marginal
overloading may shorten the service life of the generator.
1. Start the engine (page 7) and make sure the output indicator
(green) comes on.
2. Plug in the appliance.
3. Turn on the appliance.
If the generator is overloaded (in excess of 2.8 kVA), if there is a short
circuit in a connected appliance, or if the inverter is overheated, the
overload alarm (red) will come ON. The overload alarm (red) will stay
ON, and after about 4~10 seconds, current to the connected
appliance(s) will shut off, and the output indicator (green) will go OFF.
Stop the engine and investigate the problem.
Determine if the cause is a short circuit in a connected appliance or an
overload. Correct the problem and restart the generator.
8
CHOKE
ROD
OPEN
CLOSED
ON
OFF
ENGINE
SWITCH
FUEL VALVE
LEVER
OFF
AC Applications
Before connecting an appliance or power cord to the generator:
• Make sure that it is in good working order. A faulty appliance or
power cord can create a potential for electrical shock.
• If an appliance begins to operate abnormally, becomes sluggish, or
stops suddenly, turn it off immediately. Disconnect the appliance,
and determine whether the problem is the appliance or if the rated
load capacity of the generator has been exceeded.
Most appliance motors require more than their rated wattage for
startup.
Make sure the electrical rating of the tool or appliance does not
exceed the maximum power rating of the generator.
Maximum power is: 2.8 kVA
For continuous operation, do not exceed the rated power.
Rated power is: 2.5 kVA
In either case, the total power requirements (VA) of all appliances
connected must be considered. Appliance and power tool
manufacturers usually list rating information near the model number
or serial number.
NOTICE
Substantial overloading that continuously lights the red overload
alarm may damage the generator. Marginal overloading that
temporarily lights the red overload alarm may shorten the service life
of the generator.

Eco Throttle System

With the switch in the ON
position, engine speed is
automatically lowered when
electrical loads are reduced,
turned off, or disconnected.
When appliances are turned on
or reconnected, the engine
returns to the proper speed to
power the electrical load. In the
OFF position, the Eco Throttle
system does not operate and
the engine runs at high speed.
Appliances with large start-up power demands may not allow the
engine to reach normal operating rpm when they are connected to the
generator. Turn the Eco Throttle switch to the OFF position and
connect the appliance to the generator. If the engine still will not reach
normal operating speed, check that the appliance does not exceed
the rated load capacity of the generator.
If high electrical loads are connected simultaneously, turn the Eco
Throttle switch to the OFF position to reduce voltage changes.
The Eco Throttle system is not effective for use with appliances or
tools that require only momentary power. If the tool or appliance will
be turned ON and OFF quickly, the Eco Throttle switch should be in
the OFF position.
ECO-THROTTLE
SWITCH
ON
OFF