Related Manuals for mundoclima CL23390
Summary of Contents for mundoclima CL23390
- Page 1 Duct 100% fresh air MVD DC Installation manual CL23390 to CL23394 English www.mundoclima.com...
-
Page 2: Table Of Contents
Installation manual Duct 100% fresh air Disassembling,replacement and maintenance of filter CONTENTS PAGE should be carried out by qualified person. INSTALLATION PRECAUTION..............1 The appliance shall not be installed in the laundry. INSTALLATION PLACE................1 If the supply cord is damaged, it must be replaced by the ACCESSORIES..................2 manufacturer or its service agent or a similarly qualified person INDOOR UNIT INSTALLATION ..............2... -
Page 3: Accessories
Installation manual Duct 100% fresh air ● There is combustible gas or materials. The following are selectable accessories ● There is much evaporating acid or alkaline gas. Remote controller & Its Frame ● Other special areas. 1. Remote controller........1 Notes Before Installation ●... - Page 4 Installation manual Duct 100% fresh air Wooden construction Take out the air-in grill. Put the square timber traversely overthe roof beam, then Dismantle the air filter install the hanging screw bolts. (Refer to Fig.4-1) Clean the air filter (Vacuum cleaner or pure water may be Timber over the beam used to clean the air filter.
- Page 5 Installation manual Duct 100% fresh air The positioning of ceiling hole and indoor unit and hanging screw bolts routine method of installation: the size of installation for indoor unit following the Fig.4--9 and Fig.4-10 12.5~14kW Unit: mm PLASTIC COVER ELECTRICAL CONTROL AIR INTAKE 4-12*25 OBLONG SUSPENTION BOLT HOLES...
- Page 6 Installation manual Duct 100% fresh air Position A Water Tray Position B 12 Screw For fixing the safety drain tray Safety Drain Tray Fig.4-11 1. The whole unit status show as Fig.4-10. 2. Remove the all 11 screw from fixed Safety Drain Tray, and then take off the tray as figure showed in Fig.4-11. 3.Take off the tray along the direction of the arrow show in Fig.4-11.
- Page 7 Installation manual Duct 100% fresh air The method of installation: Adopt following method if the air-conditioning’s size of installationsite is limited and the indoor unit can’t put into the installtionsite. Fig.4-12 Position A Water Tray Position B 11-Screw Safety Drain Tray Fig.4-13 1.
- Page 8 Installation manual Duct 100% fresh air maintenance of motor 4 Bolts For fixing the fan assembly Filter Motor Assembly Safety Drain Tray 12-Screw For fixing the satety drain tray Fig.4-14 Inside of structure Front view of fan assembly installation state Side view of fan assembly installation state Pothook...
- Page 9 Installation manual Duct 100% fresh air Maintenance of motor: 4 Bolts For fixing the fan assembly FIiler Fortified panel Motor Asseembly 4 Screw For fixing the reinforced panel Safety Drain Tray 11-Screw For fixing the satety drain tray Fig.4-16 Inside of structure Front view of fan assembly installation state Side view of fan assembly installation state...
- Page 10 Installation manual Duct 100% fresh air 20kW 1121 25kW 28kW Entrances and exits for communication lines of indoor and outdoor Air outlet 4-12*25 oblong 1440 suspention bolt holes Electrical parts box 4- 10 hanging screw Air outlet (configure on spot) duct flange Connecting point Refrigerant-pipe flared...
-
Page 11: Installation Space
Installation manual Duct 100% fresh air The indoor unit show as Fig.4-19 NOTE Following Fig.4-20 twist-off the screws, along the direction of A During teardown and installation, the scroll was allowed direct get off the cover plate A and cover plate B. support by hand Dismounting bolt A Fan subassembly is more weightiness, please take careful... -
Page 12: High Static Pressure Type
Installation manual Duct 100% fresh air 6. HIGH STATIC PRESSURE TYP Canvas tie-in Canvas tie-in Air inlet Outer wall 12.5/14KW Isolation booth Air outlet Isolation booth checking orifice Air dust filter Fig.7-1 Installation of fan duct Connect the fan duct as the following. (Refer to Fig.7-2 ) (Air intake side) Connecting air duct and intake flange Provided at field... -
Page 13: Throtting Components Maaintenance
Installation manual Duct 100% fresh air 8. THROTTING COMPONENTS MAAINTENANCE 11. INSTALL THE CONNECTING PIPE The throttling components of Model 125, 140 are built in, when the ● Check whether the height drop between the indoor unit and throttling components built in dismountable formaintenance, please outdoor unit, the length of refrigerant pipe, and the number of open the piping maintaining cover panel directly, anduse two the bends meet the following requirements:... -
Page 14: Refrigerant Pipe Connection
Installation manual Duct 100% fresh air 12.2 Check The Leakage Use frozen oil Check all the joints with the leak detector or soap water. (See Fig.10-6 as a reference illustration) Fig.11-1 Check-point of indoor unit Bend the pipe with thumb Fig.11-2 Check-point of outdoor unit Make the ends... -
Page 15: Connect The Drain Pipe
Installation manual Duct 100% fresh air All the stop valves should be opened before test operation. Fasten the nut Each air conditioner has two stop valves of different sizes on ● Put the connecting tubing at the proper position, wrench the the side of the outdoor unit which operate as Lo-stop value, respec- nuts with hands then fasten it with a wrench. -
Page 16: Wiring
Installation manual Duct 100% fresh air Put as deep as possible (about 10mm) CAUTION A disconnection device having an air gap contact separation in all active conductors should be incorporated in the fixed wiring according to the National Wiring Regulation. Downward declivity VP30 lower than 1/100... -
Page 17: Control
Installation manual Duct 100% fresh air INDOOR UNIT Fig.14-4 Please use 3-core shielding wire, and ground the shielding layer. 15. CONTROL Mainboard For 125/140 models Note: 1.The functions in the dashed rectangle are available for particular Air-conditioner. 2. SW2-SW4,SW6 must be set as this diagram. 3.ENC2 is used for Static Pressure, must be set acoording to the INSTALLTION MANUAL. - Page 18 14000W(5.0HP) must activate the Auto-address dip-switch (except 3 pipes system). 16000W(6.0HP) Note: To make the addressing you can contact with Mundoclima after sales service. NOTE Mainboard codes indication label 200T1(8.0HP): Please dial switch ENC1 to B for system A and 8 for system B.
- Page 19 Installation manual Duct 100% fresh air SW 3 Difinition SW 3 Difinition 00 means the time of stopping 00 means the time of stopping TERMAL fan is 4 mintues TERMAL fan is 4 mintues 01 means the time of stopping 01 means the time of stopping TERMAL fan is 8 mintues TERMAL fan is 8 mintues...
- Page 20 Installation manual Duct 100% fresh air For both T1 SW 2 Difinition 00 means shutting down the unit J1, J2 Difinition to “stop cold air” at 15 1234 without jumper fo r " J 1 " auto restart function 01 means shutting down the unit to “stop cold air”...
-
Page 21: Trouble Shooting
Installation manual Duct 100% fresh air 16. TROUBLE SHOOTING 17. INSTALL ELECTRIC THROTTLE PART Please refer to the following figures to install. Table.16-1 Error code Indication Timer LED and run LED No address when first time Connective Pipe 1 flash together,or show power on "FE"... -
Page 22: Test Operation
Installation manual Duct 100% fresh air 19. TEST OPERATION CAUTION The test operation must be carried out after the entire installation Protection function will delay the startup of compressor for 3 has been completed. minutes in case the unit is turned on immediately after power on or restarted after shutdown. - Page 23 Installation manual Duct 100% fresh air NOTES:...
- Page 24 ASK FOR MORE INFORMATION Phone: (+34) 93 446 27 80 eMail: info@mundoclima.com TECHNICAL ASSISTANCE Phone: (+34) 93 652 53 57 www.mundoclima.com...
Need help?
Do you have a question about the CL23390 and is the answer not in the manual?
Questions and answers