Advertisement
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified
electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II
symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
9
1.5.
BATTERY chARGER SAFETY INSTRucTIONS
WARNING! DO NOT attempt to charge any battery other than that supplied for the wrench. other types
‰
of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.3 above.
9
Disconnect the charger from the mains supply when not in use.
9
DO NOT charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
8
DO NOT expose the charger to damp or wet conditions.
8
DO NOT pull or carry the charger by the power lead.
8
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised
8
agent for repair or obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
8
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
8
DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow the
8
unit to cool for 15 minutes before charging the next pack.
8
DO NOT attempt to connect two chargers together.
8
Store the charger in the same manner as the battery pack in 1.2.
9
2.
INTRODucTION
i
Variable speed trigger for greater control. Cast aluminium gearbox. Rubber gearhead cover. Thermal overload protection. Double injection
body with rubber grips for added comfort. Produces torque of up to 400Nm(295lb.ft). Fitted with electronic brake. LED Work light
illuminates work area when trigger is pressed. Supplied in storage case with 3Ah Li-ion battery and 80 minute mains charger.
3.
SPEcIFIcATION
I
MODEL NO: ......................................... cP400LI/cP400LIhv
Battery: ...........................................................18V 3Ah Li-ion
Drive: ......................................................................... 1/2"Sq.
no load speed: ......................................................0-2200rpm
Impact Rate: ......................................................... 0-2700bpm
Maximum Torque: ..........................................400Nm(295lb.ft)
noise power/pressure ...............................................93/82dB
Vib/Uncertainty .................................................. 8.93/1.5 m/s
Replacement battery ............................................. CP400BP
4. BATTERY
4.1.
chARGING ThE BATTERY PAcK
4.1.1. Remove the battery pack from the wrench, by depressing the release clip (fig.1.5).
WARNING! DO NOT touch metal terminals.
‰
4.1.2.
Place wrench in carry case and remove the battery charger.
4.1.3.
Connect the charger to the mains electricity supply. The green LED will light continuously until a battery is inserted.
4.1.4.
The battery pack has the positive (+) and negative (-) terminals marked. Align the battery with its docking point and insert it into slot.
NOTE: The battery pack is designed so that it will only enter the charger unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack firmly into the power terminals.
4.1.5.
When a battery is inserted correctly, the chargers red charge light will show a steady illuminated aspect whilst the battery is charging.
When fully charged the light will show green.
4.1.6.
The battery charge level can be queried by pressing the button to the right of the three LEDs on its the rear face. If fully charged, all three
LEDs will light.
NOTE: When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several
4.1.7.
subsequent charges may also take a little longer than when the battery pack reaches its optimum performance. Afterwards,
normal charging time is approximately 80 minutes.
4.1.8.
After removing the battery by depressing the release clip (fig.1.5), disconnect the charger from the mains supply and store in the carry
case as described in section 1.2.
IMPORTANT WARRANTY INFORMATION:
‰
The battery pack fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over
time. We will guarantee it against mechanical and electrical defect for a period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will
not replace the battery pack even if it is less than one year old. Remove battery pack from case and charge as above:
© Jack Sealey Limited
2
Original Language Version
REcOMMENDED
FuSE RATING: 5AMP
CP400LIHV Issue 1 26/11/19
Advertisement
