Table of Contents
Advertisement
Operating the appliance
This appliance only works when it is completely extended.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Extending/retracting the appliance
:
Risk of injury!
Risk of jamming when retracting and extending the appliance.
Never reach into the moving area of the appliance while it is
being retracted or extended. Keep children at a safe distance.
:
Risk of injury!
Cookware set down within the movement area of the appliance
can fall over. Hot liquids that pour out can cause injury. Do not
set down any cookware within the movement area of the
appliance.
Note: If the appliance has been temporarily disconnected from
the power supply, it will retract fully.
Extending the appliance
Remove any objects from the area of movement of the
1.
appliance.
Press the
button.
#
2.
The appliance extends fully. The fan starts at setting 2.
Retracting the appliance
Note: The filter cover must be closed completely.
Remove any objects from the area of movement of the
1.
appliance.
Press and hold the
button for two seconds.
#
2.
The appliance retracts fully. The light and fan are
automatically switched off.
Setting the fan
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
Switching on the appliance
Press the
button.
#
1.
The fan starts at setting 2.
Press the "+" or "-" buttons to set another fan setting.
2.
Switching off the appliance
Press the
button.
#
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Two different intensive settings are available:
– duration: 5 minutes
›‚
›ƒ
– duration: 7 minutes
Press the
button.
›
■
Intensive setting
is activated.
›‚
Press the
button again to activate intensive setting
›
■
Once the preset time has elapsed, the electronics automatically
switch the fan back to the setting at which it was operating
previously. If you wish to end the intensive setting before this
time has elapsed, press the
button.
›
Fan run-on time
Press the
x
1.
The fan continues to operate for a further 15 minutes at the
previous setting, and then switches off automatically after this
time. The remaining run-on time is displayed in minutes in the
display panel. If the lighting is switched on, this is also
switched off after the run-on time.
Press the
x
2.
The fan run-on ends before the end of the remaining run-on
time.
Lighting
The lighting can be switched on and off independently of the
ventilation.
Press the
@
button.
Setting the brightness
Press and hold the
1.
The brightness is reduced.
Press the
@
2.
The maximum brightness is restored.
Saturation display
When the metal grease filter or activated charcoal filter is
saturated, the corresponding symbol flashes:
Metal grease filter:
■
Activated charcoal filter:
■
When this happens, do not delay cleaning the metal grease
filter or replacing the activated charcoal filter any further.
For instructions on how to clean the metal grease filter, please
refer to the section "Cleaning and maintenance".
Restoring the saturation displays
Switch off the motor.
1.
Press and hold the "-" button for two seconds.
2.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
Check that the extractor hood is connected and switched off.
1.
Press and hold the "+" button for two seconds.
2.
flashes twice, i.e. the electronic control is switched over to
'
circulating-air mode.
Press the "+" button.
3.
flashes once, i.e. the electronic control is switched back to
'
exhaust-air mode.
.
›ƒ
button.
button again.
@
button for two seconds.
button.
ª
'
7
Advertisement
Table of Contents
