Ubiquiti UniFi UAP-IW Quick Start Manual
  1. Manuals
  2. Brands
  3. Ubiquiti Manuals
  4. Access points
  5. UniFi UAP-IW
  6. Quick start manual

Ubiquiti UniFi UAP-IW Quick Start Manual

In-wall wi-fi access point
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
In-Wall Wi-Fi Access Point
Model: UAP-IW

Advertisement

Table of Contents
loading

Related Manuals for Ubiquiti UniFi UAP-IW

Summary of Contents for Ubiquiti UniFi UAP-IW

  • Page 1 In-Wall Wi-Fi Access Point Model: UAP-IW...

  • Page 2: Package Contents

    Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® In‑Wall Wi‑Fi Access Point. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Important: UniFi Controller v5.x is recommended for managing the UAP-IW and is available for download at: downloads.ubnt.com/unifi...

  • Page 3: Network Topology Requirements

    Network Topology Requirements • A DHCP-enabled network (for the AP to obtain an IP address as well as for the wireless clients after deployment) • A management station running the UniFi Controller software, located either on-site and connected to the same Layer-2 network, or off-site in a cloud or NOC UAP-IW UniFi Cloud Key...

  • Page 4: Hardware Overview

    Hardware Overview PoE Out + Data Reset PoE In + Data Data PoE Out + Data 10/100 Ethernet port supports data and PoE. Used to connect an 802.3af device to the LAN. Data 10/100 Ethernet port supports data only. Used to connect a client device to the LAN.
  • Page 5 LED Color Status Factory default, waiting to be integrated. White Initializing. Flashing White Device is busy; do not touch or unplug it. Alternating This usually indicates that a process such White/Blue as a firmware upgrade is taking place. Indicates the device has been successfully Blue integrated into a network and is working properly.

  • Page 6: Hardware Installation

    Hardware Installation An electrical wall box should be pre‑installed with an Ethernet cable running from the box to a UniFi Switch. 1. Detach the Cover Plate from the UAP-IW. 2. Connect the Ethernet cable in the wall box to the port labeled PoE IN + DATA.
  • Page 7 3. Place the UAP‑IW in the wall box and properly position the cable to ensure the Ethernet connection is not strained. Note: If the wall box does not have enough room to accommodate the UAP-IW without straining the Ethernet connection, replace the wall box with an open‑end or deeper box.
  • Page 8 4. Fasten the top and bottom screws. Adjust the screws to ensure the mounting plate is flush with the wall for proper fitting of the Cover Plate. Note: Do not over‑tighten or rely on the force of the screws to pull the UAP‑IW into the wall box.
  • Page 9 5. Attach the Cover Plate. Press the Cover Plate into position until the four mounting clips snap into place. If you are using your own cover plate, secure it with two screws.

  • Page 10: Software Installation

    Software Installation Download and install the latest version of the UniFi Controller software at: downloads.ubnt.com/unifi Launch the software and follow the on‑screen instructions. Step‑by‑step instructions are available in the User Guide located on our website: documentation.ubnt.com/unifi After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface.

  • Page 11: Specifications

    Specifications UAP‑IW Dimensions 114.6 x 70.6 x 28.5 mm (4.51 x 2.78 x 1.12") Weight 117 g (4.127 oz) Networking Interface (3) 10/100 Ethernet Ports Button(s) Reset Power Method UniFi Switch (PoE) Power Save Supported PoE Out 48V Pass-Through (Pins 1, 2+; 3, 6-) Max.

  • Page 12: Safety Notices

    Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm.

  • Page 13: Limited Warranty

    Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;...

  • Page 14: Limitation Of Liability

    SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING.

  • Page 15: Industry Canada

    EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.

  • Page 16: Rf Exposure Warning

    This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UAPRO) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type...

  • Page 17: Rohs/Weee Compliance Statement

    CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert Sign (!) Follows CE Marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.
  • Page 18 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.

  • Page 19: Declaration Of Conformity

    [German] Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Ελληνική Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις [Greek] βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.
  • Page 20 ©2012-2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHSwitch, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.

Table of Contents