Related Manuals for Grundig GCA-B3322D
Summary of Contents for Grundig GCA-B3322D
- Page 1 Owner's Manual Cameras & Domes GCA-B3322D 1/3" CCD Fixed Dome Camera, Vari-Focal GCA-B3326D 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED GCA-B3322D.44.1.09.02.2012 © ASP AG...
-
Page 3: Table Of Contents
Content: 1. Available Versions 2. Important Safety Instructions 3. Package Contents 4. Installation 1. Part Names 2. Base Installation 3. Connections 4. 3-Axis Gimbal Adjustment 5. Zoom & Focus Adjustment 6. IR-LED On/Off Switch 5. OSD Control Keys 6. OSD Menu 1. -
Page 4: Available Versions
Continued use in such a condition may cause fire or electric shock. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (GRUNDIG is not liable for problems caused by unauthorised modifications or attempted repair.) To prevent fire or electric shock, do not expose the inside of this device to rain or moisture. -
Page 5: Package Contents
3. Package Contents These parts are included: 4. Installation Do not install the product in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. Keep out of direct sunlight and heat radiation sources. This may cause fire. Avoid aiming the camera directly towards extremely bright objects such as the sun, as this may damage the image sensor. -
Page 6: Part Names
4.1. Part Names 1. Bubble 2. Dome Cover Ring 3. Mounting Screws 4. Camera Module Gimbal Bracket 5. Lens 6. Dome Base 7. Service Monitor Output Port 8. Video Out and Power Cable English... -
Page 7: Base Installation
4.2. Base Installation 1. Open the dome cover ring at the marked position (e.g. with a flat screw driver). 2. There are three mounting holes on the Dome Base for installation of the unit in any place such as a ceiling, wall and etc. Use the three mounting screws to affix the Dome Base to a sturdy surface. -
Page 8: Connections
4.3. Connections - Power connection: Requires a DC 12V or AC 24V input depending on the camera model. - All camera models are supplied with a service monitor output on the camera module. A control cable is included in the package. Note: To set up the OSD menu externally, a control cable is required. -
Page 9: Axis Gimbal Adjustment
4.4. 3-Axis Gimbal Adjustment 1. Pan: Adjust the pan by turning it manually to the right or left. 2. Tilt: Adjust the tilt by moving it manually up or down. 3. Rotation: Adjust the rotation manually to the desired angle. 4.5. -
Page 10: Ir-Led On/Off Switch
4.6. IR-LED On/Off Switch For the cameras with IR-LEDs, it is possible to switch off the LEDs. Please turn the switch to ON or OFF according to your needs. - OFF: Select OFF if the subject in the picture has an extreme IR-LED refelction. - ON: Select ON if the subject has no IR-LED reflection. - Page 11 LENS: Here you can configure the lens setting. SHUTTER/AGC: This function is used to control the light exposure. WHITE BAL: You can control the white balance under different lighting conditions here. PICT ADJUST: You can set different picture related settings like mirroring, brightness, contrast, hue and gain.
-
Page 12: Lens
6.1. LENS You can select MANUAL or AUTO mode for this function, depending on the lens type. AUTO: Here you can set the operation mode of the lens and adjust the iris speed. - TYPE [DC, VIDEO] : Please do not select VIDEO mode. -
Page 13: White Bal (White Balance)
HIGH LUMINANCE - MODE [AUTO IRIS, SHUT+AUTO IRIS] : When choosing AUTO IRIS, the electronic shutter is fixed, and the exposure is controlled using the mechanical iris. When choosing SHUT+AUTO IRIS, the auto exposure is controlled by using the electronic shutter in middle-bright light conditions, and using the mechanical iris in high-bright conditions. - Page 14 ATW: In this mode, the camera automatically tracks changes in the colour temperature, and adjusts the white balance according to the ambient conditions. - SPEED [000~255] : Sets the speed of searching for White Balance when the colour temperature changed. - DELAY CNT [00~255] : This sets the delay time of searching for White Balance, when the colour temperature changed.
- Page 15 USER2: This mode is the fixed fluorescent light gain mode and is fitted for indoor lighting conditions. - B-GAIN: Adjusts the White Balance for the colour Blue. - R-GAIN: Adjusts the White Balance for the colour Red. ANTI CR: With this function you can minimise the problems related to colour rolling caused by the flickering of fluorescent lights.
-
Page 16: Pict Adjust (Picture Adjustment)
6.4. PICT ADJUST (Picture Adjustment) MIRROR [ON, OFF] : This function is used to inverse the camera picture. BRIGHTNESS [000~255] : This function is used to adjust the brightness of the camera picture. CONTRAST [000~255] : This function is used to adjust the contrast of the image (the difference between light and dark areas on the screen). -
Page 17: Backlight
LUMINANCE [LOW, MID, HIGH] : This improves the visibility of bright areas. CONTRAST [LOW, MIDLOW, MID, MIDHIGH, HIGH] : This improves the visibilty of dark areas. 6.7. BACKLIGHT This function is used for backlight compensation. Please choose from OFF, BLC and HLC. -
Page 18: Day/Night
6.9. DAY/NIGHT This function is used to improve the camera's sensitivity at night or when the brigthness level of the ambient environment is low. AUTO [BURST, DELAY CNT, DAY→NIGHT, NIGHT→DAY] : This mode automatically switches the video signals between COLOR and B/W when the according ambient illumination/brightness is reached. -
Page 19: Motion Det (Motion Detection)
- BURST: Set this option to ON to output a burst signal in B/W mode. - IR OPTIMIZER: Set the IR OPTIMIZER to ON to control the screen overexposure caused by the camera's bright LED light in dark ambient conditions. - MODE: Choose CENTER if the subjects which can cause overexposure are located near the centre of the monitored area. -
Page 20: Privacy
AREA SEL [1/4 ~ 4/4] : Here you can select the setting for each monitoring area. - TOP: Sets the top side of the selected monitoring area. - BOTTOM: Sets the bottom side of the selected monitoring area. - LEFT: Sets the left side of the selected monitoring area. - RIGHT: Sets the right side of the selected monitoring area. -
Page 21: Camera Reset
6.14. CAMERA RESET All the settings will be restored to factory default. 6.15. NEXT / BACK When you select NEXT, the second main menu page will be shown. When you select BACK, the first main menu page will be shown. 6.16. - Page 22 Specifications GCA-B3322D Image Sensor 1/3" CCD Sony 960H Ex-view HAD II Scanning System PAL, 50Hz, 625L (V), 2:1 Inter Line Transfer Pixels - Effective 976(H) x 582(V) Resolution 700 (H) lines colour Col/B&W Auto (Electrical) / Color / B/W Sensitivity Colour 0.1 Lux (50IRE) @ F1.2...
- Page 23 Power Consumption 1.7 (4.1 LED on) W Weight 0.5 kg Dimensions (wxhxd) Ø 122 x 95 mm Dimensions English...
- Page 24 EC Declaration of Conformity GCA-B3322D 1/3" CCD Fixed Dome Camera, Vari-Focal GCA-B3326D 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED It is hereby certified that the products meet the standards in the following relevant provisions: EC EMC Directive 2004/108/EC...