Table of Contents
Advertisement
Owner's Manual
12 V Cordless Drill
54-2893-4
CAUTION:
Before using this
cordless drill or any of
its accessories, read
this manual and follow
all its Safety Rules and
Operating Instructions.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Rev 1
11/01/05
General Safety Rules
Specific Safety Rules
and Symbols
Functional Description
Assembly
Operation
Maintenance
Accessories
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for jobmate 54-2893-4
- Page 1 Owner’s Manual 12 V Cordless Drill 54-2893-4 General Safety Rules CAUTION: Specific Safety Rules Before using this and Symbols cordless drill or any of Functional Description its accessories, read Assembly this manual and follow Operation all its Safety Rules and ...
-
Page 2: Table Of Contents
17 – 18 WARRANTY 1-year Warranty This JobMate product carries a one (1) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge with the same model or one of equal value or specification, within the stated warranty period, when returned by the original purchaser with proof of purchase. -
Page 3: Product Specifications
SPECIFICATIONS: DRILL Motor speeds: 0–500 RPM (no load) Battery: 12 V Clutch positions: 17 including drill mode ” Keyless chuck: Weight: 6 lb. 3 oz. (2.8 kg) BATTERY & CHARGER Battery Voltage …………… 12 V Charger ……………………. 3–5 Hour, Class 2 Charger Input ……………... -
Page 4: Power Tool Safety
POWER TOOL SAFETY GENERAL SAFETY RULES Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an WARNING: Read and understand all outlet. Keep cord away from heat, oil, sharp instructions. Failure to follow all edges or moving parts. - Page 5 POWER TOOL SAFETY TOOL USE AND CARE SERVICE Use clamps or other practical way to Tool service must be performed only by secure and support the workpiece to a qualified personnel. Service or stable platform. Holding the work by hand maintenance performed by unqualified or against your body is unstable and may personnel could result in risk of injury.
-
Page 6: Drill Safety
POWER TOOL SAFETY SPECIFIC SAFETY RULES – cont’d Do not charge the battery if it is wet To avoid injury from accidental or shows any evidence of corrosion. starting, always remove the battery from the tool before installing or removing a A small leakage from the battery may drill bit, saw blade, sandpaper, occur under extreme usage, charging or... -
Page 7: Symbols
BATTERY & CHARGER SYMBOLS SAFETY kilograms newtons per square Do not operate charger if it has N/cm centimeter received a sharp blow, been dropped or otherwise damaged in any way. pascals Have a qualified technician examine the charger and repair it if necessary. -
Page 8: Know Your Cordless Drill
KNOW YOUR CORDLESS DRILL Screwdriver bit storage Keyless chuck Clutch Forward / reverse switch Trigger switch Battery Charger stand Battery charger... -
Page 9: Accessories
ACCESSORIES & CARTON CONTENTS CARTON CONTENTS – cont’d AVAILABLE ACCESSORIES WARNING: Use only accessories DRILL COMPONENTS recommended for this cordless drill. DESCRIPTION Follow instructions that accompany Drill accessories. Use of improper Double ended accessories may cause injury to the screwdriver bits operator or damage to the cordless drill. - Page 10 CARTON CONTENTS...
-
Page 11: Assembly & Operation
ASSEMBLY & OPERATION CHARGING THE BATTERY INSTALLING BATTERY IN TOOL Place the charging stand near a Remove the discharged battery (1) from 110–120 V/60 Hz electrical outlet. the tool by pressing on the battery release buttons (2) on each side of the Insert small charger plug (1) into battery and pulling the battery out of the charger stand (2) and plug the battery... - Page 12 ASSEMBLY & OPERATION SCREWDRIVER BIT STORAGE Convenient screwdriver bit storage (1) is provided at the rear of the drill housing (see Fig. 3). Fig. 4 FORWARD/REVERSE SWITCH The forward/reverse switch (1) is conveniently mounted above the trigger Fig. 3 switch (2) (see Fig.5). To make the drill TORQUE ADJUSTMENT rotate clockwise (for drilling) push the forward / reverse switch to the left.
- Page 13 ASSEMBLY & OPERATION NOTE: Drilling at a slow drilling speed for an Finish tightening the chuck jaws by extended period of time may cause the drill holding the chuck collar with one hand motor or the battery pack to overheat. If the and firmly tightening the chuck body by drill or battery get hot, stop drilling and allow rotating it in a clockwise direction.
- Page 14 ASSEMBLY & OPERATION Check drill bit to make sure it is firmly locked into the drill chuck and the WARNING forward/reverse switch is in the forward position. Have you read “POWER TOOL SAFETY”, “DRILL SAFETY”, Set torque clutch to highest setting. “BATTERY &...
- Page 15 ASSEMBLY & OPERATION DRIVING SCREWS Tap the hex key sharply with a mallet (4) in a clockwise direction. This action When driving screws, care must be taken to will loosen the screw in the chuck for use the bit that correctly fits the screw being easy removal.
-
Page 16: Maintenance
After installing the chuck once it has been When servicing, use removed, the chuck may become loose on only identical JobMate™ replacement the spindle and develop a wobble. Also, the parts. Use of any other part may create a chuck screw may become loose causing the hazard or cause product damage. -
Page 17: Parts & Service
PARTS DIAGRAM – MODEL 54-2893-4 Cordless Drill... - Page 18 PARTS LIST – MODEL 54-2893-4 Cordless Drill When servicing, use only JobMate™ replacement parts. Use of any WARNING: other parts may create a HAZARD or cause damage to your power tool. Any attempt to repair or replace electrical parts on this power tool may create a hazard unless repair is performed by a qualified technician.
Need help?
Do you have a question about the 54-2893-4 and is the answer not in the manual?
Questions and answers