Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Powerline A2 SPECIAL EDITION
Summary of Contents for Powerline A2 SPECIAL EDITION
- Page 1 A2 Red Rotary Laser SPECIAL EDITION INSTRUCTION MANUAL...
- Page 2 SAFETY Please read this instruction manual before operating this product. Please store this instruction manual in the carry case for future reference. CAUTION: Class 2 Laser Product Do not stare directly into the laser beam from apertures. Do not disassemble the instrument or attempt to perform any internal servicing as this will void your warranty.
-
Page 3: Item Checklist
Please ensure the following items are included with your laser. If anything is missing please contact your retailer. 90° 45° 10° INCHES 180° Laser glasses Remote control Detector and clamp Laser target Powerline A2 Carry case Charger Rechargeable Alkaline battery pack battery pack... -
Page 4: Product Overview
PRODUCT OVERVIEW Protective lighthouse Rotating laser port Control panel... -
Page 5: Control Panel
CONTROL PANEL Y-axis up Scanning mode Counter clockwise rotation 90° 45° 10° 180° Speed control Clockwise rotation Y-axis down Manual / automatic mode Tilt alarm Tilt alarm indicator Manual / automatic mode indicator Power indicator Power... - Page 6 DETECTOR CONTROL PANEL LCD display screen Laser sensor Coarse / fine mode Power Sound on / off Bubble vial Speaker...
-
Page 7: Remote Control Panel
REMOTE CONTROL PANEL Button indicator Speed control Scanning mode 90° 45° 10° 180° Manual / automatic mode Counter clockwise rotation Clockwise rotation Y-axis up Y-axis down... - Page 8 USING YOUR LASER Power Supply ‣ The Powerline A2 is supplied with a rechargeable Ni-MH battery pack that is located in the base of the unit. ‣ It is recommended that the battery pack be completely charged before use. ‣ Charging time is approximately 5 hours.
- Page 9 Horizontal Set Up ‣ Select a place as close as practical to the work site. Ensure the location is clear of traffic. ‣ Attach the laser to a tripod and place on a level surface. Ensure the unit is secured correctly and tightened in position. Vertical Set Up ‣...
- Page 10 Speed control ‣ Press the speed control button to cycle through various rotational speeds. ‣ The speed control indicator will flash slowly when speed is slow and fast when speed is increasing. Scanning mode ‣ To focus the laser beam between two points press the scanning mode button.
- Page 11 Setting up grades / slopes ‣ To create slopes and grades enter into manual mode by pressing the manual / automatic mode button. ‣ The manual / automatic mode indicator will light up when in manual mode. ‣ To adjust the grade use the Y-axis up or Y-axis down arrows. ‣...
- Page 12 Using Your Detector ‣ Switch the detector on by pressing the power button. The speaker will beep once indicating the unit is operating. ‣ The LCD screen will display the battery level, detection mode and speaker function. ‣ To change between coarse and fine mode press the coarse / fine mode button ‣...
- Page 13 Using Your Remote ‣ Ensure the unit is turned on and the laser is rotating. ‣ Press the speed control button to increase or decrease the speed of the lasers rotation. ‣ To focus the laser beam between two points press the scanning mode button.
-
Page 14: Checking Calibration
CHECKING CALIBRATION Before doing any precision levelling it is advised to check the calibration of the unit. ‣ Set up the laser on a tripod at about 30m facing a wall or staff with a detector. ‣ Allow the unit to level. ‣... -
Page 15: Troubleshooting
TROUBLE SHOOTING Laser does not turn on ‣ Check the batteries. They may be in the wrong way or need replacing. ‣ Check the battery compartment for signs of damage. Ensure they are clean and not bent. ‣ Connect the main power adaptor. Laser turns on but does not rotate ‣... - Page 16 Detector does not detect the laser beam ‣ Check the batteries. They may be in the wrong way or need replacing. ‣ Check that the laser is operating correctly. Detector speaker is not functioning ‣ Check sound is on. ‣ Check the laser is operating correctly and producing a beam.
-
Page 17: Care And Maintenance
CARE AND MAINTENANCE ‣ Reflective surfaces such as glass may reflect the beam, causing two beams to strike the detector at the same time. This may create inaccurate reference points. ‣ This is a precision instrument and should always be transported within the carry case provided. -
Page 18: Warranty
WARRANTY The Powerline A2 comes with a 6 year manufacturers warranty. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. -
Page 19: Specifications
SPECIFICATIONS Specifications Powerline A2 Product code 50039 Warranty 6 Years Accuracy ±1.5mm at 30m Range 500m Levelling range ±9% / ±5° Laser class 2 Red Battery life 20 hours Battery type 4x C (sealed pack) IP rating Weight (kg) 2.00... - Page 20 www.spoton.com.au...
Need help?
Do you have a question about the A2 SPECIAL EDITION and is the answer not in the manual?
Questions and answers