WINGTOP SH-6510 User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Introduction

------------------------

Overview

The SH-6510 is only 1U Four in one control center (KVM switch,

KEYBOARD, LCD and MOUSE). It can control up to 8 PCs or 64

PCs by cascade. There is no interface card or software to configure.

Installation is as easy as connecting cables between SH-6510 and

your computers. Operation is as simple as pressing push button,

entering hot-key command and navigating through the user-friendly

on-screen menu. Depending on the model you have, it switches up

to 4 (KVM104D), 8 (KVM108D) IBM-compatible computers.

KVM Switches is independent of the computer operating system.

Two-Console KVM Switches (Optional)

The advanced multi-access KVM Switches enable you to control

multiple computers from two different locations: one is contained in

SH-6510; the other one you can connect from outside, the distance is

up to 30M. KVM208D controls 8 computers.

On-Screen Display (OSD) Menu

For KVM104D, KVM108D,

KVM208D models

For KVM Switches with built-in OSD control, you can name your

computers, switch to a computer from a list, configure settings with

easy-to-use menus, view the name of the selected computer

on-screen with programmable time interval. The OSD displays the

system status throughout operation.

For Monitor with built-in OSD control, you can be easy to set up your

monitor.

SH-6510 User Guide

The

Automatic Mouse Conversion

The KVM Switches enable you to connect computers with PS/2 or

serial mouse ports (using adapters supplied with each KVM Switches)

and control the computers from one PS/2 mouse(Touch pad). The

KVM Switches automatically identifies the mouse and switches to

proper mouse protocol.

High Video Quality

KVM Switches supports VGA resolution up to 1600x1200 @85Hz

without any degradation (But it is limited by Monitor, so only up to

Monitor resolution). Advanced VGA circuit design guarantees smooth

and flicker-free switching from one computer to the other with

distance up to 100ft (30M)* at both Console and PC sides.

NOTE: The following is the optional KVM Switch and Display models.

Optional KVM Switch Models

OSD

KVM104D

Optional switch

No. of console

supported

No. of PC supported

Optional DISPLAY Models

Optional

12.1

DISPLAY

Display's

800x600

1024x768

Resolution

SH-6510 User Guide

KVM108D

KVM208D

13.3

14.1

15.0

1024x768

Table of Contents

Summary of Contents for WINGTOP SH-6510

Page 1 Overview The KVM Switches enable you to connect computers with PS/2 or The SH-6510 is only 1U Four in one control center (KVM switch, serial mouse ports (using adapters supplied with each KVM Switches) KEYBOARD, LCD and MOUSE). It can control up to 8 PCs or 64 and control the computers from one PS/2 mouse(Touch pad).
Page 2 SH-6510 User Guide SH-6510 User Guide Features * Tested with high-quality UL2919-rated, low-loss and shielded cables. Supports both PS/2 and serial mouse Cascade configuration expands system capability up to 64 PCs Auto-scan automatically selects computers sequentially Supports Microsoft IntelliMouse (Pro)
Page 3: Single Configuration
KVM Switches, as shown in figure 1. Figure 2: A cascade KVM Switches configuration Throughout this manual, Master is the SH-6510. Slave is a KVM Figure 1: A single configuration Switches that has its CONSOLE port connected to a Master's “PC x”...
Page 4: Initial Power-Up
SH-6510 User Guide SH-6510 User Guide Installation ------------------------ Initial Power-Up Device Connection Make sure all computers and KVM Switches are powered down during installation. You must power up the Master KVM Determine the channel address of each computer. For computers Switches before turning on any other devices.
Page 5: Rack Mount Accessories
Figure 6 shows how to attach optional mounting brackets to the SH-6510 unit for standard 19-inch rack cabinet. Figure 7: Assembling rack cable support Then, keyboard/mouse/monitor cables can be routed over the cable Figure 6: Attaching rack mount bracket support.
Page 6: Multimedia Module
SH-6510 User Guide SH-6510 User Guide Operation ------------------------ Multimedia Module Front Panel Push Buttons An optional multimedia A/V module (MAV108) is used to select You may select a computer by pressing the front panel push button microphone, speaker and monitor signals from one out of eight directly, by issuing hot-key commands or by activating the OSD computers.
Page 7 SH-6510 User Guide SH-6510 User Guide KVM Switch OSD (On-Screen-Display) Operation MENU'. The color of a device name is green if it has power and is KVM104D,KVM108D,KVM116D,KVM208D,KVM216D ready for selection (its corresponding front panel indicator is green), or the color is white as it has no power. OSD menu updates the color when it is activated.
Page 8 SH-6510 User Guide SH-6510 User Guide Scan mode. In this mode, the KVM Switches automatically switches from one power-on computer to the next sequentially in a Function key <F3>: To lock a device (a computer or a Slave) fixed interval. During Auto Scan mode, the OSD displays from unauthorized access, use Security.
Page 9 SH-6510 User Guide SH-6510 User Guide MI as MIddle, Scan Rate Sets the duration of a computer displayed in Auto Scan ESC: To exit the OSD, press the <ESCAPE> key. mode. The options are 3 seconds, 8 seconds, 15 seconds and 30 seconds.
Page 10 SH-6510 User Guide SH-6510 User Guide Hot-key commands RETURN RETURN Hot-key command is a short keyboard sequence to select a computer, POSITION IMAGE POS. to activate computer scan, etc. KVM Switches interprets keystrokes HORIZONTAL for hot-keys all the time. A hot-key sequence starts with two left VERTICAL <CTRL>...
Page 11: Touch Pad
SH-6510 User Guide SH-6510 User Guide next computer in sequence. The length of the Auto Scan interval Touch Pad (Scan Rate) is adjustable, see below. To abort the Auto Scan mode, press the left Ctrl key twice. Note: For OSD models, Scan Type determines whether eye mark is There are two function buttons on the Touch Pad (function similar necessary during Auto Scan.
Page 12 SH-6510 User Guide SH-6510 User Guide Cascade Configuration --------------- Connection Before connecting a device (a computer or a Slave) to the Master under power, you must turn off the device. The Master must have equal or more 'PC x' ports than that of the Slave, i.e., if KVM104D is the master, KVM104 can be Slaves, but KVM108 can not.
Page 13 SH-6510 User Guide SH-6510 User Guide Multi-access KVM Switches ------------- KVM208D For OSD model: Overview After connection completes, you should re-activate the OSD menu to check if the Master recognizes the Slaves. A triangle mark ( ) is placed to the right of...
Page 14: Operation
SH-6510 User Guide SH-6510 User Guide Appendices ------------------------ Operation Specifications: On power up, the KVM208D is in Idle mode broadcasting VGA signal SH-6530-KVM104 SH-6530-KVM108 from the selected computer and detecting for keyboard and mouse Specifications and B) are both SH-6530-KVM104D SH-6530-KVM108D activity.
Page 15: Troubleshooting
Manual Scan mode works for .Press any other key to abort occasionally. jack for the SH-6510. Scan power-on computers only Manual Scan mode. .Scan type is eye mark .Set proper Scan type in OSD...
Page 16: Limited Warranty
SH-6510 User Guide Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFIT, LOSS OF BUSINESS, OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE PRODUCT EXCEEDS THE PRICE PAID FOR THE PDOCUDT.,...