Subscribe to Our Youtube Channel
Related Manuals for Barco RETRO GRAPHICS 2100
Summary of Contents for Barco RETRO GRAPHICS 2100
- Page 1 BARCO PROJECTION SYSTEMS RETRO GRAPHICS 2100 R9001310 INSTALLATION MANUAL Date : 220198 Art. No : R5975978...
- Page 2 Produced by BARCO NV, January 1998. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco on the web : http://www.barco.com Printed in Belgium...
-
Page 3: Table Of Contents
Switching to standby .................................. 3-7 Switching off ....................................3-7 Lamp life ...................................... 3-8 Fuses ......................................3-8 ENABLING/DISABLING THE PASSWORD ............................... 4 How to enable or disable the password ............................ 4-1 How to change the password menu ............................4-2 5975978 RETRO GRAPHICS 2100 220198... -
Page 4: Unpacking & Projector Dimensions
¯ 1- Power cord with outlet plug type CEE7. ¯ 1- Remote Control Unit, plus one 9V battery. & ¯ 1- Owner's Manual & ¯ 1- Installation Manual & ¯ 1- Safety Manual 5975978 RETRO GRAPHICS 2100 220198... -
Page 5: Projector Dimensions
Unpacking and Projector Dimensions Projector dimensions (mm/") All measurements shown are in millimeters and inches. 5975978 RETRO GRAPHICS 2100 220198... -
Page 6: Installation Set Up
(rear side,) and securing through the far underside of the projection CPG@T hole opening. This will require some care in manoeuvring as the fixing is recessed when the two cabinets are in place. Ensure each screw is tightened fully by hand. 5975978 RETRO GRAPHICS 2100 220198... -
Page 7: Mirror Positioning
It is now necessary to focus the corners of the picture by adjusting the Front Rotary Lens Ring (a), moving the desired amount in the anti clockwise direction. (a) Front Rotary Lens Ring (b) Main Lens Barrel Tube (c) Locking Fastener Ring 5975978 RETRO GRAPHICS 2100 220198... -
Page 8: Power Up Considerations
AC and 230V AC. Consult a qualified service technician to alter Power cord connection POWER / MA -10/6Amp the input voltage to the correct voltage to that on the wall outlet. Freq -60/50Hz This projector may be connected to an IT-power system. 5975978 RETRO GRAPHICS 2100 220198... -
Page 9: Ac Power Cord Connection
ÃSTÃ!"!ÃDI Ã8USGÃ Internal mains connection permanently connected Attention The Retro Graphics 2100 - R9001310 leaves the factory to operate Internal power switch always to be positioned in the ’1’ (ON) state on a mains (power) input of 230V AC. Alteration of the power input of the projector from 230V AC to 120V AC, or vice versa is possible. - Page 10 Ž,a. The leftside panel is removed by removing all its fixing screws Ž both on the front and back. Once the screws are removed gently lever evenly out of its position. LEFTSIDE PANEL FRONT FIXING SCREWS Ž î LEFTSIDE PANEL BACK FIXING SCREWS 5975978 RETRO GRAPHICS 2100 220198...
- Page 11 Ü Note: Extra care must be observed not to damage or scratch the projector lens during the rotating process. 23(5$7,21$/ 326,7,21 5(029$/ 326,7,21 Û 23(5$7,21$/ 326,7,21 5(029$/ 326,7,21 UPÃS@HPW@ÃASPHÃS@6S 5975978 RETRO GRAPHICS 2100 220198...
-
Page 12: Changing The Projector Input Voltage
Remove the top cover by loosening or undoing its fixing screws as indicated above. Then slide the cover backwards slightly and lift off, PROJECTOR the internal structure will be now visible. COVER PROJECTOR FIXING PROJECTOR BRACKET FIXING BRACKET SCREWS 5975978 RETRO GRAPHICS 2100 220198... - Page 13 PLUG ‘ To switch between 120V AC and 230V AC all that is required is ‘ to unplug the selector plug and turn it around, the plug is in the 230V position. VOLTAGE SELECTOR PLUG-230V 5975978 RETRO GRAPHICS 2100 220198...
-
Page 14: Switching On
- press firstly the STAND-BY key and allow projector to cool down until the fans stop blowing (or at least 15 min). - then switch off the projector with the power switch on the front local control panel. 5975978 RETRO GRAPHICS 2100 220198... -
Page 15: Lamp Life
R9829600) max. Operating the lamp longer than the lamps corresponding hours may damage the projector. Replace always with a same type of lamp. Call a BARCO authorized service technician for lamp replacement. X6SIDIB Gh€ƒÃ…ˆÃ‡v€rÃv†Ã Ãu‚ˆ…† WARNING : Using a lamp for longer than its Pƒr…h‡vtÇurÃyh€ƒÃy‚tr…... -
Page 16: Enabling/Disabling The Password
To achieve this remove the four fixing screws and carefully lift clear the cover plate. The password strap METAL on the controller circuit board module will now be visible. COVER PLATE 5975978 RETRO GRAPHICS 2100 220198... -
Page 17: How To Change The Password Menu
<ENTER> <EXIT> to return. Press ENTER to save the new entered password. Press EXIT if no changes have to be made. CHANGE PASSWORD Enter new password 0000 Select with then <ENTER> <EXIT> to return. 5975978 RETRO GRAPHICS 2100 220198...
Need help?
Do you have a question about the RETRO GRAPHICS 2100 and is the answer not in the manual?
Questions and answers