Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Ubiquiti PBE-M5-400-ISO
- Page 1 5 GHz airMAX Bridge with ® 400 mm RF Isolated Reflector Model: PBE-M5-400-ISO...
-
Page 2: Package Contents
Mounting Bracket (Qty. 4) * The PBE-M5-400-ISO Antenna Feed has a thin gray ring around the center of the cap to differentiate it from the PBE-M5-300-ISO Antenna Feed. TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. -
Page 3: Hardware Overview
Hardware Overview Bottom View Radome Antenna Feed Technology Ethernet Port Reset Button Release Button Reflector Mounting Bracket Alignment Pins Rear Housing Release Button Slot Cable Door... - Page 4 Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.
-
Page 5: Application Examples
Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable... -
Page 6: Installation
Installation 1. Align and insert the tabs of the Mounting Bracket into the slots of the Reflector. Rotate the Mounting Bracket counterclockwise until the alignment holes in the dish and bracket align with each other. 2. For added support in high-wind environments, insert four Screws with Washers into the holes in the Reflector and Mounting Bracket, and secure each screw with a Washer and a Nylon Insert Lock Nut. - Page 7 3. Line up the Alignment Pins of the Rear Housing with the alignment holes of the Mounting Bracket. Push the Rear Housing into the Mounting Bracket. 4. View the Reflector from the front. Ensure that the three hooks (indicated below) of the Rear Housing are fully engaged with the inner wall of the Reflector and locked into place.
- Page 8 5. Push in the sides of the Cable Door and detach it from the Rear Housing. 6. Attach the Antenna Feed. a. Insert the Antenna Feed into the Rear Housing, and push until it locks into place with a click. b.
- Page 9 7. Connect an Ethernet cable to the Ethernet Port of the Antenna Feed. Then re-attach the Cable Door to the Rear Housing. 8. Attach the Pole Clamp to the Adjustment Bracket. a. Hold the Adjustment Bracket with its clamps facing you and the Elevation Indicators towards the top.
- Page 10 9. Mount the Adjustment Bracket on the pole and secure it. a. Place the Adjustment Bracket against the pole. b. Slide the slot of the Pole Clamp over the adjacent Carriage Bolt. c. Tighten the Flange Nuts of the bolts to 25 N ∙ m to secure the Adjustment Bracket to the pole.
- Page 11 10. Insert the Pivot Pins on the inside of the Adjustment Bracket into the Mounting Bracket Slots. Mounting Bracket Slot Pivot Pin (one on each side of Adjustment Bracket)
- Page 12 11. Secure the Adjustment Bracket to the Mounting Bracket using the four Hex Bolts with Washers.
- Page 13 12. Align the Notch on the Reflector with the Arrow at the top of the Radome. Guide the Radome’s side and top tabs over the Reflector rim and slide the Radome down onto the Reflector. Arrow Radome Top Tab Notch Radome Side Tab Radome...
- Page 14 13. Snap the bottom three tabs of the Radome over the Reflector rim. Bottom Tabs 14. Adjust the elevation angle. a. Loosen the four Hex Bolts on both sides of the antenna. b. Pivot the antenna until the Elevation Indicator shows the desired elevation angle.
- Page 15 Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter. • Using a separate PoE switch: Connect the Ethernet cable from the device’s Main Ethernet port to a PoE-enabled Ethernet port on the switch.
- Page 16 Accessing airOS Verify connectivity in the airOS Configuration Interface. 1. Make sure that your host system is connected via Ethernet to the device. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3.
- Page 17 Customize additional settings as needed to complete the configuration. For additional details on the airOS Configuration Interface, refer to the User Guide available at www.ubnt.com/download/airmax You can also manage your device using the Ubiquiti Network Management System. Setup using the UNMS app requires ™...
-
Page 18: Installer Compliance Responsibility
Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna and Output Power fields are provided to the professional installer to assist in... -
Page 19: Specifications
Specifications PBE-M5-400-ISO Dimensions with Radome 459 x 459 x 261 mm (18.07 x 18.07 x 10.28") Weight (Mount Included) 3.22 kg (7.10 lb) Gain 25 dBi Networking Interface (1) 10/100/1000 Ethernet Port Enclosure Outdoor UV Stabilized Plastic Max. Power Consumption Max. -
Page 20: Safety Notices
(the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under... -
Page 21: Warranty Conditions
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. -
Page 22: Limitation Of Liability
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. - Page 23 Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 24: Australia And New Zealand
CAN ICES-3(A)/NMB-3(A) Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : l’appareil ne doit pas produire de brouillage; l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. -
Page 25: Rohs/Weee Compliance Statement
The following apply to products that operate in the 5 GHz frequency range: Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz frequency range within all member states. Note: All countries listed may operate at 30 dBm. BFWA member states may operate at 36 dBm. - Page 26 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 27: Declaration Of Conformity
Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa PBE-M5-400-ISO u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ubnt.com/compliance Čeština [Czech] Tímto UBIQUITI NETWORKS prohlašuje, že typ rádiového zařízení PBE-M5-400-ISO je v souladu se směrnicí... -
Page 28: Online Resources
Slovenčina [Slovak] UBIQUITI NETWORKS týmto vyhlasuje, že rádiové zariadenie typu PBE-M5-400-ISO je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.ubnt.com/compliance Slovenščina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme PBE-M5-400-ISO skladen z Direktivo 2014/53/EU.