Summary of Contents for IC Realtime ICIPB1300VIR
- Page 1 HD IR Waterproof Fixed Network Camera (With Integrated Bracket) User’s Manual Version 1.0.1...
- Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;...
- Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 1.3.1 Performance ......................2 1 channel analog video output，BNC port..................3 Structure ............................4 Multiple-function Combination Cable ................ 4 Framework and Dimension ..................5 Bidirectional talk...................... -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera product uses standard H.264 video compression technology and G.711a audio compression technology, which maximally guarantee the audio and video quality. -
Page 7: Specifications
Day/Night mode auto switch. Built-in IR light. Support IR night vision. Support picture parameter setup such as electronic shutter and gain setup. Backlight compensation: screen auto split to realize backlight compensation to adjust the bright. Support video watermark function to avoid vicious video modification. -
Page 8: Channel Analog Video Output，Bnc Port
Support mirror. Video Flip Support flip function. Snapshot Max 1f/s snapshot. File extension name is JPEG. Privacy Mask Supports max 4 privacy mask zones Image Support parameter adjustment such as bright, contrast. adjustment Video Channel title, time title, motion detect, tampering. Information Lens Motorized zoom 2.8-12 mm@F1.4... -
Page 9: Structure
2 Structure 2.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure 2- Figure 2-1 Multiple-function combination cable 1 Please refer to the following sheet for detailed information. Port Name Function Connection Note Power port. -
Page 10: Framework And Dimension
Port Name Function Connection Note Audio input Input audio signal. It can receive the analog AUDIO IN port audio signal from the pickup. Audio output Output audio signal to the devices such as AUDIO OUT port the sound box. Video output Output analog video signal. -
Page 11: Bidirectional Talk
Figure 2-3 Model b Figure 2-4 Dimension illustration 3 2.3 Bidirectional talk 2.3.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC. Login the Web and then click the Audio button to enable the bidirectional talk function. -
Page 12: Alarm Setup
Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to the audio output port of the device. Login the Web and then click the Audio button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the audio talk function. - Page 13 Figure 2-6 Alarm input Please refer to the following figure for alarm output information. See Figure 2-7. Port ALARM_COM and Port ALARM_NO composes an on-off button to provide the alarm output. If the type is NO, this button is normal open. The button becomes on when there is an alarm output. If the type is NC, this button is normal off.
-
Page 14: Installation
3 Installation Please note all frame and dimension illustrations provided in this chapter are for reference only, and actual product may vary. 3.1 Device Installation Please refer to Figure 3-1 for installation information according to the actual product. Please follow the steps listed below to install the device. -
Page 15: Lens Adjustment
Figure 3-2 Micro SD card installation 3.3 Lens Adjustment Turn counter clockwise to remove the lens cover, now you can see the iris front and rear control rod. The front control rod is to focus and the rear control rod is to zoom. See Figure 3-3. Please turn clockwise to fix the lens cover back firmly. -
Page 16: Bracket Adjustment
Figure 3-3 Lens adjustment 3.4 Bracket Adjustment You can use an M4 inner hex screw to control the bracket. Please use the inner hex wrench from the installation accessories bag to unfasten the screw. Please refer to Figure 3-4 or Figure 3-5 according to the actual product. - Page 17 Figure 3-4 Bracket adjustment 1...
-
Page 18: Osd Buttons
Figure 3-5 Bracket adjustment 2 3.5 OSD Buttons Please refer to the following contents for detailed information. See Figure 3-6 and Figure 3-7. Top button: Focus zoom in Bottom button: Focus zoon out. Left button: Far. Right button: Near. - Page 19 Figure 3-6 OSD button 1 Figure 3-7 OSD button 2...
-
Page 20: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 21 In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-3. In Figure 4-3, you can view device IP address, user name, password and port.
-
Page 22: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 23 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
-
Page 24: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device. factory default setup. Micro card Do not set the Micro SD card as the storage media to storage the write times schedule record file. -
Page 25: Appendix Toxic Or Hazardous Materials Or Elements
7 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Case ○ ○ ○ ○ ○ ○...