Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for B2 Audio SLD5K
- Page 1 MODEL: SLD5k Product id:sld5k15d SLD5k OWNER’S MANUAL...
-
Page 2: Table Of Contents
Introduction We thank you for purchasing our amplifiers. Your decision to be part of something different is what we strive for. Our products reflects who we are, going to the extent to deliver you our finest comes natural. to upgrade the stock electrical system. Ensure the system is in accordance with the full performance of the amplifier. www.facebook.com/sweetlikedanish - www.youtube.com/b2audio - www.b2audio.com - www.twitter.com/b2_audio - wwww.instagram.com/b2_audio Better Bass Better Bass is our philosophy of adding something extra. -
Page 3: Design Features
Description of specifications Stable impedance load of the SLD5K is 1 Ohm. *SLD5KL is a regulated version of the SLD5K, power output is 3000 W at 14.4 V, though at 18 V performance is the same as SLD5K * Speaker overload * Short circuit * Input Voltage - RCA &... -
Page 4: Panel Layout
Panel layout SLD5k BASS REMOTE GAIN SUBSONIC BOOST FREQ. PHASE POWER MASTER PROTECT 0.2V 10Hz 50Hz 30Hz 90Hz 35Hz 250Hz SLAVE SPEAKER OUTPUT INPUT INPUT MASTER SLAVE If unstrapped, set as Master. (Unpressed INPUT BASS BOOST RCA signal input for Left & Right channel. - Page 5 Panel layout Head unit sld5k POWER POWER GROUND* * Keep ground as short as possible, no longer than 20” (50 cm). 500A (External fuse) BATTERY GND (GROUND CONNECTION) + 12V (POWER CONNECTION) Connects to the vehicle’s chassis. Connects to the positive terminal of the battery.
-
Page 6: Installation
Installation Installation considerations If you choose to install the ampli er by yourself, please read the entire owner’s manual carefully. Before you start your installation, please take all steps into consideration. If in doubt, please go to www.b2audio.com for authorized distributors / dealers that will be able to con gure your set up &... -
Page 7: Wiring Layout
Head unit sld5k POWER POWER GROUND* * Keep ground as short as possible, no longer than 20” (50 cm). 500A (External fuse) BATTERY We recommend to use minumum12 Ga speaker cables to acquire the intended performance. Run the speaker cables from your speakers to the ampli er’s mounting location. -
Page 8: Speaker Wiring - Single Amp
Speaker Wiring Diagram - single amplifier SLD5k BASS REMOTE GAIN SUBSONIC BOOST FREQ. PHASE POWER MASTER PROTECT 0.2V 10Hz 50Hz 30Hz 90Hz 35Hz 250Hz SLAVE SPEAKER OUTPUT INPUT INPUT MASTER SLAVE If unstrapped, set as Master. (Unpressed Speaker impedance 1 Ohm ~ 8 Ohm Loads under what is speci ed will cause excessive heat &... - Page 9 Speaker Wiring Diagram master SLD5k BASS REMOTE FREQ. GAIN SUBSONIC BOOST PHASE POWER MASTER PROTECT SLAVE 0.2V 10Hz 50Hz 30Hz 90Hz 35Hz 250Hz SPEAKER OUTPUT INPUT INPUT MASTER SLAVE Leave Master unpressed Linking or strapping makes 2 ampli ers work as a single ampli er.
-
Page 10: Strapping / Linking Steps
Strapped control panel setting steps SLD5k BASS REMOTE GAIN SUBSONIC BOOST FREQ. PHASE POWER MASTER PROTECT 0.2V 10Hz 50Hz 30Hz 90Hz 35Hz 250Hz SLAVE SPEAKER OUTPUT INPUT INPUT MASTER SLAVE Leave Master unpressed BASS REMOTE GAIN SUBSONIC BOOST FREQ. PHASE... -
Page 11: Troubleshooting
Troubleshooting The protection circuits of the ampli er prevents severe damages from faulty conditions & improper use. The protection indicatior will switch on due to short circuit connection & speaker overload, thus the ampli er will be turned o . Prior to inspecting the occurred problem, turn all levels down &... - Page 12 Items not installed by authorized dealers will be warrantied for 30 days from the original purchase. Original sales receips must be accompanied with all returns.The warranty applies to the original purchaser of the product & it being sold by authorized B2 audio dealers.