BSD-Racing BS801T Instruction Manual
  1. Manuals
  2. Brands
  3. BSD-Racing Manuals
  4. Model vehicle
  5. BS801T
  6. Instruction manual

BSD-Racing BS801T Instruction Manual

Granite monster 1/8 nitro 1/8 4wd . 21 nitroengine – poweredmonster
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BSD – Racing
GRANITE MONSTER 1/8 NITRO
1/8 4WD . 21 NITROENGINE – POWEREDMONSTER
TRUCK MODEL No: BS801T
Specifications:
Length: 504mm
Width: 385mm
Height: 208mm
Wheelbase: 335mm
Tyre size: 145*71 mm
Ground Clearance: 46mm
Engine: 21Nitro
Instruction Manual
Features:
• Advanced 4WD Drive System.
• Factory Assembled & Ready-to-Run.
• Powerful .21 Nitro Engine.
• 2 Speed Automatic Transmission.
• Oil Filled Dampers.
• 2.4GHz Proportional Radio Control System.
• Quality Bevel Gear Differential.
• 125cc Fuel Tank
IMPORTANT NOTICE
This Century UK- BSD car is very tough, but it is not indestructible. In common with all R/C
cars, stresses and vibrations cancause screws and fastenings to work loose. It is your
responsibility to carry out regular checks, tighten screws where necessary and generally
maintain the car to ensure optimum performance and reliability.
SAFETY PRECAUTIONS
This high performance radio-controlled car is not a toy. Used incorrectly it is capable of
inflicting serious harm to persons or property. It is not recommended for use by children
under 14 years of age unless supervised by a suitably experienced adult.Please read the
contents of this manualprior to operating. If you are uncertain regarding any aspect of its
safe operation please contact your Century UK - BSD dealer to seek help or advice.
www.centuryuk.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BS801T and is the answer not in the manual?

Questions and answers

Summary of Contents for BSD-Racing BS801T

  • Page 1 BSD – Racing GRANITE MONSTER 1/8 NITRO 1/8 4WD . 21 NITROENGINE – POWEREDMONSTER TRUCK MODEL No: BS801T Specifications: Length: 504mm Width: 385mm Height: 208mm Wheelbase: 335mm Tyre size: 145*71 mm Ground Clearance: 46mm Engine: 21Nitro Instruction Manual Features: • Advanced 4WD Drive System.

  • Page 2: Tools Required For Maintenance

    Equipment required for operation 1. Tools required for maintenance: WARNING! Do not use a power screwdriver to remove, install or tighten any screws that locate into plastic moulded parts. The high operating speed of these tools may cause the threads in the plastic mouldings to be damaged or stripped.

  • Page 3: Transmitter Specifications

    Transmitter Specifications: Channels : 2 Model Type : Car/Boat Frequency : 2.4GHz Power :12V DC (8 x AA batteries) Charging Port : Built-in (centre pole +) Low Voltage Warning : Yes (below 9V) Note: The antenna on the receiver must be positioned vertically to achieve optimum range(Figure 1).It must be kept away from any metallic or carbon components.

  • Page 4: Transmitter Functions

    Turn Off: 1. Stop the engine. 2. Disconnect the receiver power supply. 3. Turn off the transmitter. Failure to comply with this procedure could result in a total loss of control. Transmitter Functions: DSC FOR SIMULATOR Dual Rate IMPORTANT ALWAYS: Position the car so the wheels are not touching the ground before starting the engine.

  • Page 5: Running The Engine

    ENGINE TUNING GUIDE MAIN MIXTURE CONTROL NEEDLE The main mixture control needle points upwards from the carburettor (see image). It controls the fuel/air mixture supplied to the engine. The needle is factory set for runningin, at 2 1/2 turns out (anti-clockwise) from its fully closed position.

  • Page 6: Break-In Procedure

    STOPPING THE ENGINE To stop the engine, pinch the fuel line that runs to the carburettor. Pinching this line will restrict fuel flow and the engine will stop within a few seconds. Never place your finger over the exhaust to stop the engine. This could result in serious burns to your finger and could also cause fuel to “back-up”...

  • Page 7: Tuning Tips

    FOURTH TANK OF FUEL Lean the main mixture control needle a further ½ turn. Run the car for the tank of fuel and let cool. At this stage you should notice the car is running much smoother and the engine will be producing more power.
  • Page 8 B7053 B7054...
  • Page 13 BS903-108 Charger...
  • Page 14 BS801-011 Engine washer BS801-008 Fr/Rr body BS801-009 Alum exhaust BS801-019 Air /screw 4set post BS801-012 Gearbox unit fixation set filter W/Insert Stainless steel AL6061 Stainless steel AL6061 BS801-015 Exhaust BS801-013 Spur gear/ BS801-014 Spurgear-43T MPO-03 Knuckle Arm Set MPO-02 C HUB C HUB W/Pin spring/nylon-lock nut manifold Stainless steel AL6061...

Table of Contents