Pearl PA-7R TILE SAW Owner's/Operator's Manual
  1. Manuals
  2. Brands
  3. Pearl Manuals
  4. Power Tool
  5. PA-7R TILE SAW
  6. Owner's/operator's manual

Pearl PA-7R TILE SAW Owner's/Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

MODEL PA-7R TILE SAW
Owner's/OperatOr's Manual
RENTAL
Caution!
Read Safety and General Instructions carefully before using saw for the first time.
REV. 3
serial
number -
You should record the Serial Number of your Tile Saw on this
Owner's/Operator's Manual and on the Warranty Card. The Warranty
Card must be sent back with all the required pertinent information
for the warranty to take effect.
Covered by one or more of the following US Patents:
6,080,041; 6,119,676; 6,272,990; 6,460,533; and D458,282

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PA-7R TILE SAW and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pearl PA-7R TILE SAW

  • Page 1 MODEL PA-7R TILE SAW Owner’s/OperatOr’s Manual RENTAL serial number - You should record the Serial Number of your Tile Saw on this Owner’s/Operator’s Manual and on the Warranty Card. The Warranty Card must be sent back with all the required pertinent information for the warranty to take effect.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS page general saFetY rules FOr all pOwer tOOls ....... 3 sYMBOls .

  • Page 3: General Safety Rules For All Power Tools

    i. GENERAL SAFETY RULES FOR ALL POWER TOOLS W RNING! Read all instructions. As with all machinery there are certain hazards involved with operation and use of the machine. The following basic safety precautions should be followed at all times to reduce the risk of fire, electric shock and serious personal injury to you or others.

  • Page 4: Symbols

    21. Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Extension cord tables (refer to page 21) show the correct size to use depending on cord length and nameplate ampere rating.

  • Page 5: Features

    iii. FEATURES REUSABLE AIR FILTER 3/4 HP BRUSH MOTOR Air intake to the motor is filtered Generates more torque and is physically by a fire resistant filter, which smaller and lighter than similarly rated can be cleaned and reused. induction motors. STAINLESS STEEL WATER TRAY High durability tray...

  • Page 6: Unpacking

    v. UNPACKING Open the container and carefully lift the saw by the foam packaging and place it on a flat, level working area. Be sure that you have the following items before you discard the container: • Saw • Stainless steel water tray •...
  • Page 7 W TER PUMP INST LL TION USING THE RIP GUIDE 1. Remove the water pump from the box and 1. Set the rip guide at the desired location on the check that it is not damaged. ruler guide and tighten the threaded knob. Make sure that the rip guide is firmly tightened 2.

  • Page 8: Proper Blade Use

    CLE NING THE W TER TR Y 1. Lift the saw up from inside the water tray. 2. Flush water into the tray while holding it upright to remove any sludge buildup. 3. Replace the saw back into the tray. See Figure 4. TR NSPORTING THE S W Figure 4 1.

  • Page 9: Safe Operating Practices For Tile Saw

    Do not operate any saw without safety guards in place or with a blade diameter Blade dressing stones are available from your local Pearl larger than the maximum saw blade capacity. Warehouse. 8. Before mounting a blade on the saw clean and 14.

  • Page 10: Grounding Instructions

    • Do not attempt to cut pieces too small to IMPORTANT - If there is any tendency for the saw safely hold down on the main table. to tip or move during certain operations, such as when cutting large heavy tile; the saw must •...
  • Page 11 plug that looks like the plug illustrated in Figure 5(A). A • Always use the extension cord included with the saw. temporary adaptor, which looks like the adaptor • If an additional extension cord is needed, use only a illustrated in Figures 5(B) and 5(C), may be used to cord that is intended for outdoor use.

  • Page 12: Care And Maintenance

    x. CARE AND MAINTENANCE W RNING! For your safety before performing any maintenance on the saw turn off the power switch and unplug the power cord. GENER L RULES prevent the water pump from clogging with residual dirt. • Always clean the machine before performing any After wet cleaning and before using the machine maintenance/ repair.
  • Page 13 W TER PUMP M INTEN NCE Fastener When the machine has not been used for a long period of time, hard packed dirt may begin to build up inside the pump Left Guide Rail and block the pump wheel. If the machine is activated with the immersion pump blocked, the electric motor of the pump will be damaged within a few minutes! Please follow Fastener...

  • Page 14: Electrical Motor Specifications

    Recommendations: • It is recommended that a 7.5 amp circuit be used while operating this PA-7R TILE SAW saw. This will prevent possible power interruption or loss. • Always plug saw as close as possible to the power source while...

  • Page 15: Replacement Parts List

    xii. REPLACEMENT PARTS LIST pa-7r Cutting taBle asseMBlY 13 11 3 PART NAME PART NUMBER PART NAME PART NUMBER TC02 cutting table PA00001 12 M8 x 1.25 x 30L Socket head bolt PA00012 Ruler guide PA00002 13 608 LLU radial bearing PA00013 D12.7 d8.5 x 6L spacer PA00003...
  • Page 16 pa-7r MOtOr asseMBlY – 16 –...
  • Page 17 pa-7r MOtOr asseMBlY pa-7r Main asseMBlY PART NAME PART NUMBER Blade shaft gear PA00023 Cutting head housing PA00024 Cutting head mounting tube PA00025 Blade shaft PA00026 Gear cover PA00027 Blade guard mounting shaft PA00028 Wire anchor plate PA00029 Wire separation plate PA00030 Wire access plate PA00031...

  • Page 18: Troubleshooting

    Clean and check guide roll or adjustments, Blade dressing stones are available from your local Pearl according to the procedure in the care and maintenance Warehouse. section.

  • Page 19: The Right Blades Does The Right Job

    Pearl reserves the right to discontinue products at any time without notice. All illustrations displayed in this manual are the property of Pearl Abrasive Co. and shall not be duplicated or reproduced without the express written consent of Pearl Abrasive Co.
  • Page 20 CORPORATE OFFICE: SO. CALIFORNIA • USA 6832 E. SLAUSON AVE., COMMERCE, CA 90040-0031 562-927-5561 • FAX 562-928-3857 Toll Free: 800-969-5561 www.pearlabrasive.com GEORGIA • USA ONTARIO • CANADA 4963 SOUTH ROYAL ATLANTA DRIVE 375-2 PIDO ROAD TUCKER, GEORGIA 30084 PETERBOROUGH, ONTARIO K9J-6X7 Part No.

Table of Contents