Subscribe to Our Youtube Channel
Summary of Contents for Sporty's SP-200
- Page 1 SP-200 BOOKLET 9/28/04 5:46 PM Page 3 Sporty’s SP-200 Handheld NAV/COM Operator’s Manual © 2003 Sportsman’s Market, Inc.
- Page 2 SP-200 BOOKLET 9/28/04 5:46 PM Page 4 Simplified Directions 1. Install the batteries. 2. Turn the unit on (rotate volume knob clockwise). 3. Enter the first six digits of desired frequency (1 2 2 9 7 5 for 122.975 MHz).
-
Page 3: Table Of Contents
SP-200 BOOKLET 9/28/04 5:46 PM Page 5 Table of Contents General Information ........2 Introduction . -
Page 4: General Information
Page 6 General Information Introduction This manual contains only operational information relative to Sporty’s SP-200 NAV/COM. This manual is not intended as a service or maintenance manual and does not contain any theory or schematic diagrams. Features Sporty’s SP-200 is a hand-held, aircraft communication and navigation transceiver with the following features: •... -
Page 5: Warranty
Note: When returning your unit for warranty service, do NOT include any accessories (belt clip, headset adapter, etc.). If your SP-200 is no longer under warranty, you may still have it serviced at Sporty’s. Call Sporty’s Customer Service at 513.735.9000 for instructions. -
Page 6: Batteries
9/28/04 5:46 PM Page 8 On top of the SP-200 is a BNC connector, which is standard for use on aircraft radios. Therefore, little difficulty should be encountered in connecting an existing aircraft radio antenna to the SP-200. When using the flexible antenna inside an aircraft or other enclosure,... - Page 7 The storage life of Nicad batteries is not as predictable as Alkaline batteries. The Nicad Battery Pack is recommended when the SP-200 will be used on a daily or frequent basis. The following table is a conservative estimate of the life of a fully charged Nicad Battery Pack at some common duty cycles with the audio background noise silenced by the Squelch.
-
Page 8: Precautions
SP-200 BOOKLET 9/28/04 5:46 PM Page 10 Precautions • Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment. • Never attempt to service this unit yourself. It should be referred to qualified service personnel. - Page 9 • If operating the transceiver at temperatures outside the range of -20°F to 122°F (-30°C to 50°C), the LCD (screen) may not display the selected frequency. If the SP-200 is used in temperatures lower than the recommended range, the characters being displayed may change very slowly. These...
-
Page 10: Controls
SP-200 BOOKLET 9/28/04 5:46 PM Page 12 Controls LAST FREQ SP-200 LIGHT ALL CLR DC 9V KEY LOC MEM CLR SP-200 LEFT SIDE FRONT RIGHT SIDE... -
Page 11: Top View
SP-200 BOOKLET 9/28/04 5:46 PM Page 13 This section serves only to identify and briefly describe the SP-200’s external features. Please see the Operating Instructions section for detailed instructions on the use of the SP-200. Top View Antenna Connector The flexible rubber antenna or an external antenna may be attached to this BNC connector. -
Page 12: Left Side View
Indicator (CDI) and other information to the operator. Internal Speaker Internal Microphone Numeric Keypad These keys are used whenever the SP-200 requires a numeric input such as setting the frequency or Omni Bearing Selector (OBS). Down Key/Key Lock Key This key is used to select the next lower frequency, select the next lower OBS setting or to initiate search and scan functions. -
Page 13: Right Side View
The wrist strap (included as standard equipment) attaches to this location. External Power Jack The SP-200 may be powered externally, with or without a battery pack attached, or the Nicad batteries charged by plugging the optional 12/24 Volt Cigarette Lighter Power Adapter (#8634A) or the 115 Volt Wall Power Adapter (#8633A) into this location. -
Page 14: Operating Instructions
Six digits are always required to select a frequency. The SP-200 will return to the previous frequency if there is a pause of five seconds or more between key entries while entering a new frequency. -
Page 15: Frequency Search
Search. When a broadcasting signal is found, the word SEARCH will flash and the SP-200 will stop temporarily on that frequency. If the broadcasting signal is cut off for more than two seconds, the Search will resume until another signal is found. When 142.975 MHz is reached during an upward Search, the Search automatically continues at 118.000 MHz. -
Page 16: Frequency Memory
5:46 PM Page 18 Frequency Memory The SP-200 has 20 memory channels numbered 00 to 19 to store those frequencies used most often. These memory channels may be used to store COMM and NAV frequencies. Select a desired frequency, such as 122.975, to be stored by using either manual frequency selection or frequency search. -
Page 17: Memory Recall
This frequency immediately becomes the active frequency and is received by the SP-200. 122.975 In this example, memory channel 01 is listed first, so we know that no frequency is currently being stored in memory channel 00. -
Page 18: Memory Scan
1. Press the Recall Key followed by the Up or Down Key to scroll to 08 2. Press the Recall Key followed by 0 8. Once in the Recall function, the SP-200 stays in Recall until the Clear Key is pressed. This allows you to sequence your frequencies in the order you may wish to use them. -
Page 19: Memory Clear
Once you have pressed the Clear Key to exit a Scan, you are still in the Recall function. Press the Clear Key again to exit the Recall function. The SP-200 will remain on the last frequency received. It is very important that the Squelch be properly adjusted prior to initiating a Scan. -
Page 20: Transmitting
SP-200 is broadcasting. 122.975 Release the PTT to end the transmission and the SP-200 will once again receive the selected COMM frequency. If the optional Headset Adapter is being used with the microphone plugged in the SP-200, the SP-200’s internal microphone will be deactivated and the microphone on the headset may be activated by either pressing the SP-200’s PTT or... -
Page 21: Vor Operations
When receiving a VOR signal, each division on the CDI (starting with the edge of the center circle) represents a two degree deviation. Therefore, the CDI on the SP-200 has the ability to display up to a 10 degree deviation to the right or left in VOR mode. The... - Page 22 This process may be exited any time prior to entering the third digit by pressing the Clear Key. As long as the OBS setting is flashing, the SP-200 will accept numeric inputs between 0 and 360. Once three digits have...
-
Page 23: Localizer Operations
When receiving a Localizer signal, each division on the CDI (starting with the edge of the center circle) represents a one degree deviation. Therefore, the CDI on the SP-200 has the ability to display up to a 5 degree deviation to the right or left in Localizer mode. The above example shows a 3 degree deviation to the left (fly right towards the needle to be on course). -
Page 24: Key Lock
122.975 KEY.L Key Lock is deactivated by holding the Clear key and pressing the Down key a second time. Key Lock only locks out the SP-200’s keypad. The PTT and Light functions are not affected. Screen and Keypad Lighting Press and release the Light Button to activate the SP-200’s screen and keypad lighting for five seconds. -
Page 25: Accessories
Cover covers and protects the electrical contacts on the bottom of the SP-200. Nicad Battery Pack (#8631A) The Nicad Battery Pack should be used if the SP-200 will be used on a daily or frequent basis. Requires at least one of the four available Power Adapters/Chargers (#8632A, #8633A, #8628A or #8634A). - Page 26 12, 24 or 28 Volt electrical systems (accepts input voltage of 10 to 30 Volts DC). Plugs into the side of the SP-200, which allows the unit to be powered with or without a battery pack attached. Also charges the optional Nicad Battery Pack (#8631A).
- Page 27 Custom made to allow access to the SP-200’s exterior buttons. Made of black leather with a detachable belt loop. Metal Belt Clip (#3920A) Attaches to the back of the SP-200 with screws installed in the unit as standard equipment. Suction Cup Transceiver Holder (#6489A) Allows the SP-200 to be mounted on a window or other smooth surface with a rubber suction cup.
- Page 28 Made of rugged Du Pont Cordura ® nylon this patented carrying case is an ideal way to keep the SP-200 dust-free and close at hand. Features sewn-in sleeve for antenna storage. Black carrying case features a sewn belt loop. Remote Antenna Mount (#1646A) Suction cup mount allows the antenna to be positioned in a side window or other favorable location for improved reception.
-
Page 29: Specifications
SP-200 BOOKLET 9/28/04 5:46 PM Page 31 Specifications General Communication Frequencies 2280 Frequencies from 118.000 MHz to 136.975 MHz (8.33 KHz steps) Receive Only Frequencies 720 Frequencies from 137.000 MHz to 142.975 MHz (8.33 KHz steps) Navigation Frequencies 200 Frequencies from 108.000 MHz to 117.950 MHz (50 KHz steps) - Page 30 SP-200 BOOKLET 9/28/04 5:46 PM Page 32 Frequency Stability ± 10 PPM (0.001%) at 25C Battery Pack Power Nicad Battery Pack 9.6 VDC / 600 mAH Alkaline Battery Pack 12.0 VDC (8 AA batteries x 1.5 VDC each) Receiver Audio Output...
- Page 31 SP-200 BOOKLET 9/28/04 5:46 PM Page 33 Spurious Radiation -60 dB below carrier Unnecessary Emissions -60 dB or less Power Consumption 1 A (max)
- Page 32 SP-200 BOOKLET 9/28/04 5:45 PM Page 2 Sporty’s SP-200 Handheld NAV/COM and various components are protected under patent and copyright laws of the United States of America and other nations, including U.S. Patents 4,843,399 and 5,771,018.
Need help?
Do you have a question about the SP-200 and is the answer not in the manual?
Questions and answers