Summary of Contents for Sure Slice SSG350STR
- Page 1 Professional slicer CE SSG350STR mod. Operating and Maintenance Manual SERVICE CENTRE AUTHORISED DEALER...
-
Page 2: Out Of Service
CHAP. 8 - DISMANTLING 8.1 - OUT OF SERVICE If for some reason it is decided to put the machine out of service, make sure that it cannot be used by anyone: detach or cut the electrical connections. 8.2 - WEEE Waste of Electric and Electronic Equipment Directive 2002/95/EC, 2002/96/EC and 2003/108/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment, and waste electrical and electronic equipment... - Page 3 INTRODUCTION CHAP. 7 - MAINTENANCE This manual has been re-presented to provide the Client with all the information on the 7.1 - GENERALITIES machine and its safety regulations, and also the use and maintenance instructions which Before carrying out any maintenance operations it is necessary to: permit using the machine in the best way and maintaining its efficiency throughout time.
- Page 4 - CLEANING THE MACHINE 6.2.4 - Cleaning the sharpener 6.2.1 - Cleaning the goods holder plate To clean the sharpener it is necessary 6.2.2 - Cleaning the blade, the bladeguard and the ring to adhere to the following instructions: 6.2.3 - Cleaning the sliceguard 1.
- Page 5 6.2.3 - Cleaning the blade, the bladeguard and the ring CHAP. 1 - RECEIVING THE MACHINE Unscrew the blade cover tie rod (3) and 1.1 - PACKAGE remove the blade cover (2) (Fig. n°50). The blade cover can now be cleaned. The slicer is shipped in a package which consists of (Fig.
- Page 6 6.2 - CLEANING THE MACHINE 6.2.1 - Cleaning the goods holder plate Do not expose the package to humidity or rain (Fig. n°4). The goods presser can be removed completely from the plate as follows Fig. n°4 ( Fig. n°48) : Unscrew the handgrip (4) then ...
- Page 7 5. insert the pin and start the machine, overturn the package!! When transporting it make sure that it is firmly held by the four corners (keeping it parallel to the floor by pressing the “ON” push-button; 6. press the push-button (2 Fig.n°46), let the blade rotate in contact with the grinder for about 30/40 sec.
-
Page 8: Sharpening The Blade
2.2 - 8. at the end of the cutting operation, stop the machine by putting the switch in POSITIONING the “OFF” (ARREST) position and put the graduated handgrip at “0”; 9. Carry out resharpening the blade as soon as the cut product has a threaded Position the pallet, with the slicer, on a or rough surface, therefore the cutting effort increases (chapter 5.3). -
Page 9: Loading And Cutting The Product
5.2 - LOADING AND CUTTING THE PRODUCT 2.3 - ELECTRICAL CONNECTION WARNING: The goods to be cut are loaded on the plate only with the graduated Check that the data reported on the handgrip at “0” and the motor stopped, being careful with the blade and the technical-part number plate (Fig. -
Page 10: Operational Check
the position of two of the three phase CHAP. 5 - MACHINE USE wires (black, gray or brown) in the plug. 5.1 - OPERATIONAL CHECK For the 1° use follow these instructions: Fig. n°20 check that installation has been carried out correctly as in chapter 2; 2.3.5 - Electrical connection modification check that the plate is well fastened Unless otherwise specified, the slicers are equipped with 400 V. - Page 11 2.4.2 - Single-phase 230 V. tension selection Fig. n°34 OUTPUT DIAGRAM Fig. n°35 TAB. n°1 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES 2.4.3 - Three-phase 230 V. tension selection Model U.m. SSG350STR Blade diameter Motor Watt/Hp 380/0,52 Cut thickness Run of carriage Hopper 350x320 575x410 2.4.4 - Three-phase 400 V.
-
Page 12: Preliminary Check
2.5 - PRELIMINARY CHECK - A relay in the control circuit, that requires the machine to start up again Before testing make sure the goods in case of an accidental loss of holder plate is well-blocked, after which electricity (Fig. n°33). test functioning with the following procedure: Push the “ON”... -
Page 13: Safety Devices Installed On The Machine
4.2 - SAFETY DEVICES INSTALLED ON THE MACHINE The slicer must only be used by trained personnel who know the 4.2.1 - Mechanical safety safety norms contained in this manual As far as mechanical safety is concerned, the slicer described in this manual perfectly. -
Page 14: Construction Features
Do not pull the slicer or the feeding LEGEND: cable (Fig. n°29) to unplug it. Sharpener handgrip Goods holder plate Regularly check the state of the Sharpener Blade protection feeding cable; a worn out cable or in any case not intact represents a Thickness gauge plane Base serious electrical danger.
Need help?
Do you have a question about the SSG350STR and is the answer not in the manual?
Questions and answers