Summary of Contents for COP Security 15-CD521W
- Page 1 Installation and Operation Manual Speed Dome Camera 15-CD521W/15-CD523W Please read the operation manual carefully before installing and using this unit VER:1.1...
- Page 2 SPECIFICATION ITEMS 15-CD521W 15-CD523W Zoom Camera CZ40HCM CZ55HCM SYNC System Internal Mode / External (AC Lock) Mode (±1Hz) Scanning System 1:2 Interlace Pick Up Device 1/4“ Sony Super HAD CCD Effective Pixels 768 (H) X 494 (V) (NTSC) 752 (H) X 582 (V) (PAL) More than 46 dB ( γ...
-
Page 3: Table Of Contents
CONTENTS 1. PRECAUTIONS-------------------------------------------------------- 2 2. OPERATION------------------------------------------------------------ 4 3. ID SETTING------------------------------------------------------------- 8 4. PROTOCOL SETTING----------------------------------------------- 10 5. CONSTRUCTION----------------------------------------------------- 10 5.2OUTDOOR SPEED DOME CAMERA----------------------------------------- 11 6. TROUBLESHOTING------------------------------------------------- 12 7. CONNECTION OF RS485 BUS AND TERMINATION RESISTER----------------------------------------- 13 8. INSTALLATION-------------------------------------------------------- 15 8.1 INDOOR SPEED DOME CAMERA--------------------------------------------15 8.2OUTDOOR SPEED DOME CAMERA----------------------------------------- 15 APPENDIX : MENU OF COP ZOOM MODULE -------------------... - Page 4 ● Lightning proof equipment must be installed when the speed Warnings dome camera is installed in open area. ！ ● Make sure the input voltage and normal rated power before powered up. Relation Table of DC12V Cable Diameter and Transmission distance When the cable diameters equal, and voltage wastage rate of DC12V is under 10%, the maximum transmission distance is recommended.
-
Page 5: Precautions
1. PRECAUTIONS (1) Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Ask qualified service personnel for servicing. (2) Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. -
Page 6: Operation
• Rapid temperature fluctuations due to frequent door opening and closing • Use in an environment where eyeglasses become foggy • Use in a room filled with cigarette smoke or dust. If the lens becomes cloudy due to condensation, remove the dome cover and wipe all moist surfaces with a soft cloth. - Page 7 2.3 Preset Function The speed dome camera is capable of going to 128 preset positions. Each is with its own P/T/Z and focus. （Preset positions 50-66 are reserved for auxiliary functions.） When preset a camera position, the P/T/Z and focus will be memorized for that position. 2.3.1 To set a preset position [PRESET] + nnn + [ENTER], the Monitor displays：...
- Page 8 Operation Function Call + 33 + Enter Pan 180° Call + 51+ Enter Scan start Preset + 51+ Enter Set the start position of scan Call + 52+ Enter Scan stop Preset + 52+ Enter Set the end position of scan Call + 53 + Enter Auto cruise from No.1 preset position to NO.16 preset position Preset + 53+ Enter...
- Page 9 Operation Function Call + n + Enter To call the number N preset position Preset + n + Enter To set the number N preset position Preset + n + Off Delete the number N preset position Set the dome address “n” Cam + n + Enter Shot + 1+ Enter Auto the cruise track...
-
Page 10: Id Setting
5. Special Function—Power-off Protection When the camera is under scan or cruise track, and power off occurs, the camera will save the state before the power-off. When power is resupplied, the camera will continue to perform the scan or cruise track automatically under the same state before power-off. Should scan or cruise track are not performed before power-off, the camera will stop at the first preset position automatically. -
Page 11: Protocol Setting
ˉˉˉˉˉˉˉˉˉˉˉˉ Note：Control cables can connect multiple speed dome cameras in parallel provided that No. 10 ID code of the farthest camera is set to “ON”. The operation is required when the control distance is quite far. The No. 10 ID code should be set to “ON” for the last camera connected to the daisy chain. -
Page 12: Construction
5.CONSTRUCTION 1 Wall Mount 2 DC12V Input 3 Video Output 4 RS485 data 5 Camera 6 Acylic dome 7 Aluminum Die Cast Housing ◆ CONNECTIONS PRECAUTIONS ※ The following connections should be made by qualified service personnel or system installers in accordance with all local codes. D C 12V V i deo O ut put O range R S 485+... -
Page 13: Troubleshoting
6. TROUBLESHOTING Trouble Possible Causes Solution Power supply is not well connected Replace No action, no video after Engineering cable failure Eliminate powered up The power supply is not well connected Correct Machine failure Repair The camera is declining Put straight Self-check isn’t normal, but Change power and place it near the image is normal and obstacle... - Page 14 (3) Problem in Practical Connection In some circumstances user adopts a star configuration in practical connection. The termination resistors must be connected to the two equipments (No. 6 and No. 10) that are farthest away from each other. But the connection does not meet the RS485 standards. 120Ω...
-
Page 15: Installation
8. INSTALLATION 8.1 OUTDOOR WALL MOUNT ① Take the Acylic dome apart firstly, choose the ID code and protocol code secondly, mount the Acylic dome again finally . (fig.1) ② Put the wire into the wall mount bracket, then secure the dome camera and bracket by screws. (fig.2) ③... -
Page 16: Appendix : Menu Of Cop Zoom Module
APPENDIX : MENU OF COP ZOOM MODULE How to enter the menu of COP zoom module 1. To execute the order CALL+95+ENTER into the menu. Then you will see the menu of COP module Main Menu ( Page 1. ) S E T U P M E N U ( 1 / 3 ) - Page 17 Sub Menu ◆ White Balance W H I T E B A L A N C E è C O L O R O F F è A U T O - ■ - è A T W - ■ - A W B - ■...
- Page 18 ◆ IRIS I R I S è P E A K è O F F A ■ - - ■ - è A U T O A L C - ■ - F I X - ■ - A E S A U T O è...
- Page 19 ◆ BACKLIGHT B A C K L I G H T è O F F è A R E A - ■ - S E N S L O W - - H I This is used to control “BLC” (Back Light Compensation), 1.
- Page 20 ◆ ZOOM ･ FOCUS Z O O M ▪ F O C U S è D I G I T A L Z O O M O F F - ■ - Z O O M S P E E D - ■...
- Page 21 1. 「 H.REVERSE 」 ： Horizontal Reverse (Mirror) ON/OFF 2. 「 V.REVERSE 」 ： Vertical Reverse (Up-side down) ON/OFF ◆ TITLE T I T L E è 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m...
- Page 22 “INITIAL”, “PHASE” condition 1. 「 PRESET 」 ： Set to ON camera will be reset and set to default data. 2. 「 INITIAL 」 select ： Set to ON lens is action,Set to OFF lens is not action. 3. 「 PHASE 」 adj select ： Set to OFF ext-sync is disable,Set to ON ext-VD sync is enable,(EXT-VD signal must be input) 4.
- Page 23 è N O = 1 - ■ - Z O O M S P E E D - ■ - F O C U S S P E E D Z O O M W I D E T E L E F O C U S I N F N E A R...
- Page 24 è O F F N O = 1 This is used to select the camera power on state. 1. 「 BLUE BACK 」 ： Set to OFF camaer power on initial is normal display, Set to ON camaer power on initial is display blue back.
- Page 25 6. Ver. direction start position. 7. Ver. direction end position. 8.ZOOM action to link mask area, ON / OFF select. ◆ O S D è P O S I T I O N O F F è O N è O F F M O T I O N Z O O M ▪...
- Page 26 (As show screen stillness about 5 minutes cameras come into AF Sleep mode namely, as screen has bigger change time come back again act for normal mode namely.) ◆ LANGUGE L A N G U A G E è E N G L I S H C H I N E S E J A P A N E S E This is used to select OSD manu display language.
- Page 27 ◆ CROSS LINE C R O S S L I N E è O F F This is used to select the cross line display ON / FF. Cross line ON/OFF select,set ON cross line display,set OFF cross line is hidden. ◆...
Need help?
Do you have a question about the 15-CD521W and is the answer not in the manual?
Questions and answers