Table of Contents
Advertisement
Quick Links
Slugger USA5
Slugger Portable Magnetic Drilling Machine
OPERATOR'S MANUAL
WARNING!
,
before use
be sure everyone using this machine reads and understands
.
all safety and operating instructions in this manual
ALPHA INDUSTRIAL TOOL &
EQUIPMENT
51 Tamarack Drive
Thornhill, Ont
L3T 4 W2
Canada
PH. 905-731-1310
EYE PROTECTION
HEARING PROTECTION
NEVER PLACE
LINE VOLTAGE
BEWARE OF
FAX 905-731-1044
REQUIRED
REQUIRED
FINGERS NEAR
PRESENT
ROTATING
CUTTING AREA OR
MACHINE PARTS
MACHINE ARBOR
MOdEL #18066 (120V) OR #18080 (240V)
Serial #
Date of Purchase
Advertisement
Table of Contents
Summary of Contents for Slugger 18066
- Page 1 L3T 4 W2 Canada PH. 905-731-1310 EYE PROTECTION HEARING PROTECTION NEVER PLACE LINE VOLTAGE BEWARE OF FAX 905-731-1044 REQUIRED REQUIRED FINGERS NEAR PRESENT ROTATING CUTTING AREA OR MACHINE PARTS MACHINE ARBOR MOdEL #18066 (120V) OR #18080 (240V) Serial # Date of Purchase...
-
Page 2: Table Of Contents
Motor Parts List ......... . 14 Available Slugger Cutters ........15 limited warranty Jancy Engineering Inc. -
Page 3: Important Safety Instructions
important safety instructions WARNING! when using electric tools basic safety precautions should always be followed to reduce risk of fire electric shock and personal injury READ AND SAVE ALL INSTRUCTIONS FOR FUTURE REFERENCE. 1. keep work Area clean Cluttered areas and benches invite injuries. •... -
Page 4: Guideline For Shift Lever Position
important safety instructions 13. Maintain Tools with care Keep tools sharp and clean for better and safer performance. • Follow instructions for lubricating and changing accessories. • Inspect tool cords periodically and if damaged, have repaired by authorized service facility. •... -
Page 5: Special Instructions
8. Always use proper tooling. Keep cutters securely fastened. 9. Do not use dull or broken cutters. 10. Do not use Slugger drilling machines on surfaces or materials being welded. Doing so can damage the machine’s electrical components. 11. Beware of slugs ejected at end of cut. They become HOT during the cut. -
Page 6: Grounding Instructions And Extension Cords
The plug and outlet should look like those in Figure A. WARNING! do not use slugger drilling machines on surfaces or materials being welded doing so can result in personal injury and... -
Page 7: Contents Of Package
3. When drilling materials under 3/8" thick, an additional steel plate may be required to achieve proper magnet adhe- sion. 4. Material that has been flame cut may have become heat-treated and therefore difficult to drill. Avoid drilling near such areas whenever possible. 5. Drilling with the USA5 in horizontal positions requires a special lubrication for Slugger cutters. -
Page 8: Machine Operation
6. Connect machine to power source. 7. Lower Slugger cutter to surface of material to be cut. Coolant will be released down the pilot into center of Slugger cutter. Coolant flow can be stopped by lifting pilot pin off work surface. NOTE: Be sure coolant valve is open. -
Page 9: Basic Troubleshooting
basic troubleshooting 1. Magnetic base not holding securely Material is too thin to engage magnet. • Surface of material being drilled must be free of chips, debris, rust and mill scale. • Does size of cutter exceed machine’s rated capacity? •... -
Page 10: Regular Maintenance
Drill Point Breakaway 950 lbs. on 1" plate Magnet Base Dimensions 4" x 7-1/2" Magnet Dead Lift 2320 lbs. on 1" plate Slugger Cutter Diameter (Maximum) 2-3/8" Slugger Depth of Cut (Maximum) 3" 1" note magnetic base requires minimum material... -
Page 11: Control Panel And Parts List
: 3- note inch depth slugger cutters aVailable below 3/4" diameter coolant and cutting paste slugger cutter pilot pins cutters listed aboVe description part pilot fits cutter sizes part PINT 10206W 1" DEPTH OF CUT / 1/2" DIAMETER AND SMALLER 16001...
Need help?
Do you have a question about the 18066 and is the answer not in the manual?
Questions and answers