Related Manuals for D-Link DGS-1016A
Summary of Contents for D-Link DGS-1016A
- Page 1 ® D-Link DGS-1016A DGS-1024A 16/24-PORT GIGABIT DESKTOP SWITCH Manual Building Networks for People RECYCLABLE (May 2014) V 2.00...
- Page 2 Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
-
Page 3: Table Of Contents
CONTENTS PREFACE……………………………………………………………… IV ............OTES OTICES AUTIONS ................AFETY NSTRUCTIONS Protecting Against Electrostatic Discharge ........vii INTRODUCTION ................... 8 BOUT UIDE ................8 WITCH ESCRIPTION Switch Features .................. 9 ..............10 REEN ECHNOLOGY ..............11 RONT ANEL OMPONENTS LED Indicators ................. 11 .............. -
Page 4: Preface
D-Link DGS-1016A/DGS-1024A GIGABIT DESKTOP SWITCH Preface The DGS-1016A/DGS-1024A Manual is divided into sections that describe the system installation and operating instructions with examples. Section 1, Introduction - A description of the physical features of the Switch, including LED indicators, ports and panel descriptions. -
Page 5: Safety Instructions
D-Link DGS-1016A/DGS-1024A GIGABIT DESKTOP SWITCH Safety Instructions Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions and precautions that you need to review and follow. - Page 6 D-Link DGS-1016A/DGS-1024A GIGABIT DESKTOP SWITCH Safety Instructions (continued) • To help avoid damaging your system, be sure the voltage selection Switch (if provided) on the power supply is set to match the power available at your location: – 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such as South Korea and Taiwan –...
-
Page 7: Protecting Against Electrostatic Discharge
D-Link DGS-1016A/DGS-1024A GIGABIT DESKTOP SWITCH Protecting Against Electrostatic Discharge Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do so by periodically touching an unpainted metal surface on the chassis. -
Page 8: Introduction
SOHO or small office customers. Switch Description The 16-port DGS-1016A and 24-port DGS-1024A Switches provide dedicated 10, 100 or 1000 Mbps Ethernet bandwidth on each port. The ports will automatically detect the speed, duplex and MDI/MDIX status of the device it is connecting to, and adjust these settings accordingly. -
Page 9: Switch Features
Wire-Speed reception and transmission 8K absolute MAC Address (DGS-1016A) ; 8K absolute MAC Address (DGS-1024A) 2Mbits RAM for data buffering (DGS-1016A) ; 4.1Mbits RAM for data buffering (DGS-1024A) IEEE 802.3x Flow Control for Full-duplex mode Back Pressure Flow Control for Half-duplex mode ... -
Page 10: D-Link Green Technology
Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of time. D-Link Green Technology • IEEE 802.3az Energy-Efficient Ethernet (EEE): It is the first standard in the history of Ethernet to address proactive reduction in energy consumption for networked devices. -
Page 11: Front-Panel Components
If there is no link on a port, such as when there is no computer connected to the port or the connected computer is powered off, D-Link’s Green Technology will enter a "sleep mode", drastically reducing power used for that port. - Page 12 LED Indicator Description Power This lights green while the Switch is receiving power. When connected to a 1000Mbps device, Link/Act/Speed this LED indicator light is green when the port is connected to a device and will blink as data is transmitted or received. When connected to a 10/100Mbps device, this LED indicator light is amber when the port is connected to a device and will blink...
-
Page 13: Rear Panel Description
The power cable connection is located on the rear panel of the Switch. DC Power Jack: Power is supplied through an external 12V/1A AC power adapter for DGS-1016A and an external 12V/1.5A AC power adapter for DGS- 1024A. Check the technical specification section for information about the AC power input voltage. -
Page 14: Installation
The carton should contain the following items: • One DGS-1016A 16-Port/ DGS-1024A 24-Port 10/100/1000BASE-T GIGABIT DESKTOP SWITCH • One AC power adapter • Quick Install Guide • Wall-mounting kits If any item is found missing or damaged, please contact your local D-Link reseller for replacement. -
Page 15: Before You Connect To The Network
Before You Connect to the Network The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up the Switch. • Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs.) of weight. -
Page 16: Mounting The Switch On A Rack
Mounting the Switch on a Rack The DGS-1016A /24A can be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.) Mounting on a cement wall... -
Page 17: Power On
Power On Plug one end of the AC to DC power adapter into the power connector of the Switch and the other end into the local power source outlet. After the Switch is powered on, the LED indicators will momentarily blink. -
Page 18: Connecting The Switch
Section 3 Connecting the Switch Switch to End Node Switch to Hub or Switch Connecting to a Server NOTE: All Ethernet ports auto-detect MDI/MDIX, port speed (10, 100, 1000Mbps) and duplex of the device connected to the Switch. Cable Quality For all connections to the Switch, use these rules to determine the •... -
Page 19: Connect To An End Node
Connect to an End Node End nodes include PCs outfitted with a 10, 100, or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be connected to any of the ports of the Switch. -
Page 20: Connect To Hub Or Switch
Connect to Hub or Switch These connections can be accomplished in a number of ways using a standard Ethernet cable. • A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. •... -
Page 21: Connect To Network Backbone Or Server
Connect to Network Backbone or Server Any of the 16/24 Gigabit Ethernet ports are ideal for uplinking to a network backbone or network server. Connection to a Server... -
Page 22: Technical Specifications
Appendix Technical Specifications General Standards: IEEE 802.3 10BASE-T IEEE 802.3u compliance IEEE 802.3ab compliance IEEE 802.3x Flow Control supports for Full Duplex Protocol: CSMA/CD Data Transfer Ethernet: 10Mbps (Half-duplex) Rate: 20Mbps (Full-duplex) Fast 100Mbps (Half-duplex) Ethernet: 200Mbps (Full-duplex) Gigabit 2000Mbps (Full-duplex) Ethernet: Topology: Star... - Page 23 DGS-1024A (W x D x H) : 10.1 in x 7.0 in x 1.8 inchies (257mm x 178mm x 46mm) DGS-1024A: 0.74 kg / DGS-1016A: 0.53 kg Weight FCC Class A, ICES-003 Class A, CE Class A, Tick Class A...
- Page 24 Performance Transmission Method: Store-and-forward RAM Buffer: DGS-1016A : 2Mbits per device DGS-1024A : 4.1Mbits per device Filtering Address DGS-1016A : 8K MAC address Table: DGS-1024A : 8K MAC address Packet Filtering/ Full wire speed Forwarding Rate: MAC Address Self-learning, auto-aging...
-
Page 25: Glossary
Glossary 1000BASE-T –1000BASE-T - Known as IEEE 802.3ab which is a standard for Gigabit Ethernet over copper wiring. 100BASE-TX – 100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling. 10BASE-T – The IEEE 802.3 specification for Ethernet over Unshielded Twisted Pair (UTP) cabling. - Page 26 When two devices transmit simultaneously, a collision occurs and the colliding devices delay their retransmissions for a random amount of time. Data Center Switching – The point of aggregation within a corporate network where a switch provides high-performance access to server farms, a high-speed backbone connection, and a control point for network management and security.
- Page 27 Rresilient Llink – A pair of ports that can be configured so that one will take over data transmission should the other fail. See also main port and standby port. RJ-45 – Standard 8-wire connectors for IEEE 802.3 10BASE-T networks. RMON –...