1. Manuals
  2. Brands
  3. Autostart Manuals
  4. Car security
  5. Keyless Entry and Alarm System ASL-550
  6. Installation manual

Autostart ASL-550 Installation Manual

Hide thumbs Also See for ASL-550:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
K e y l e s s
Included in the Kit................................................1
Installation Points to Remember........................2
Programmable Features......................................2
Harness Description ............................................3
5-pin harness ...............................................3
12-pin harness .............................................3
How to Flash the Hood Pin .................................4
Programming a Transmitter................................4
Entering Programming Options .........................4

Included in the Kit

Please review the installation guide before beginning the installation, especially the wiring diagram and the
programming options. It is very important that you familiarize yourself with the programming and operation of
the system, even if you have already installed an alarm system in the past. There are many great new features
that may be overlooked if the manual is not read: You would therefore not maximize the unit's potential. Prior to
the installation, make sure that all the hardware components required to install the system are in the box.
o 1 - Control unit
o 2 - 4-button transmitters
o 1 - Siren
o 1 - Plug-in LED
o 1 - Hood pin switch
o 1 - 2-pin wire harness
o 1 - 5-pin main harness
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be
that either damage to the vehicle itself or to the Unit. This Unit must be installed by a certified technician using all safety devices
supplied. Only registered technicians will be eligible to use the Autostart technical support telephone service. Please review the
Installation Guide carefully before beginning any work.
DOC. 1.00
- ASL-550TW-FM -
E n t r y
( A S
P R G - 1 0 0 0
ASL-550
Installation Guide

Table of Contents

The following is a list of the components included in the kit:
The kit also includes the following harnesses:
A n d
A l a r m
C o m p a t i b l e )
Programming Options .........................................5
Dome Light Delay.................................................7
Retain Accessory Output ....................................7
Zone 2 Disable Output.........................................7
Multi-car Operation ..............................................7
Resetting the Module...........................................7
Closing Up ............................................................8
o
o
o
o
o
o
- August 29, 2007 -
S y s t e m
1 - Plug-in shock sensor
1 - User guide
1 - Installation guide
1 - Plug-in valet button
1 - 12-pin principal auxiliary harness
1 - 3-pin connector cable
- MO -
Assembled in Canada

Advertisement

Table of Contents
loading

Related Manuals for Autostart ASL-550

Summary of Contents for Autostart ASL-550

  • Page 1: Table Of Contents

    Unit. This Unit must be installed by a certified technician using all safety devices supplied. Only registered technicians will be eligible to use the Autostart technical support telephone service. Please review the Installation Guide carefully before beginning any work.

  • Page 2: Installation Points To Remember

    Installation Points to Remember o When working on a vehicle always leave a o Always use a grommet when running wires window open. into the engine compartment. o Never leave the keys in the car. Leave them o Never run wires through bare or sharp metal. on a workbench with a window rolled down.

  • Page 3: Harness Description

    Harness Description 5-pin harness WIRE Wire colour Function Description This wire must be connected to bare, unpainted metal (the (-) CHASSIS GROUND BLACK chassis or true body ground). It is preferable that you use a INPUT factory ground bolt rather than a self-tapping screw. Connect to the +12 V power feed of the vehicle, at the Ignition +12V POWER INPUT harness.

  • Page 4: 3-Pin Connector - 2-Wire Harness

    This wire should be connected to a single pole double-throw relay: this wire will connect to pin 85 on the relay, and pin 86 will be connected to the ignition wire. 3-pin connector – 2-wire harness Wire Wire colour Function Description Programmable 500mA negative output: 1/10-sec., 7/10-sec., 4- BROWN...

  • Page 5: Programming Options

    ..........to access mode 2. The parking lights will flash and the horn will honk (if programmed) once or twice to confirm entry into a mode. Release the valet button. Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can now select the option you want in function 1.

  • Page 6: Siren / Horn Chirp Duration Adjustment

    MODE 2 * INDICATES DEFAULT SETTING FUNCTION 1 – Relock OPTION 1 DISABLED OPTION 2* – Relocks all doors 60 seconds after unlocking if neither doors nor trunk ENABLED are opened FUNCTION 2 – Chirps OPTION 1 Warning chirps only – Lock confirmation upon 2 press of button LOCK...

  • Page 7: Dome Light Delay

    Dome Light Delay When the doors are being closed and the vehicle is armed, the module will check the dome light to detect whether a door has been left open. If the dome light is on, the system will generate three chirps to warn the user that a door has been left open (There is one chirp if Mode 1 –...

  • Page 8: Diagnostics - Parking Lights Flash Rate

    Diagnostics - Parking Lights Flash Rate FLASHES & RATE DESCRIPTION CHIRPS • Locked by transmitter, system armed (starter kill, alarm) Quick • Car finder • Unlocked by transmitter, system disarmed (starter kill, alarm) Quick • System has exited valet mode •...

Table of Contents