O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Content Precaution 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 。 Chapter One Product Overview 1 ....
Page 2
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Chapter Three Function Operation 1 . Setting of preset direction position 。...
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Precautions: 1.Non-techinician is forbidden to operate this dome device before reading this manual carefully. 2.Cut the power supply off before operating the dome device to avoid damage caused by mal-operation.
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a This dome device is a hi-tech monitoring product integrating high-resolution color camera and multi-function decoder, which minimizes the wiring and installation process and enhances the reliability of the system as well as facilitates installation and maintenance.
Page 5
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a preset positions, the running speed and dwell time of which can be set and the data will not be lost when the power is off.
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Chapter Two Fast Operation Guide of Dome Device Wiring (Please do not turn the power on). 1>.
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a The communication protocol of dome device is PELCO-D 2>. 2400BPS/PELCO-P 4800BPS Setting the device address (Turn the power off when setting, and 3>.
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Install camera. (Please refer to camera installation for details). 4>. Attention: 1. Do not connect the camera and dome device with FFC in a wrong way.
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Complete the test. (Summary). .8>. 1. If the performance of item 7 is normal, it indicates the system is normal.
Page 10
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Chapter Three Function Operation I. The setting of preset direction position (note: the operation mode differs for different dome device controller, Please read the manual of the controller before operation) Preset direction position: No.
Page 11
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a 2 ) Users can set the starting point by pressing “PRESET+52+ENTER” and set the ending point by pressing “PRESET+53+ENTER”.
Page 12
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a At the same time, the tilt movement can be changed. VI Camera menu operation: Invoke(Call) No.57 preset position entry. Input “Tele”...
Page 13
O p e r a t i o n M a n u a l M i n i D o m e C a m e r a Chapter Four Trouble Shooting Problems Possible Causes Solutions After power on, no motion and Power supply damage or low Replace no image.
Need help?
Do you have a question about the LN42 and is the answer not in the manual?
Questions and answers