Table of Contents Table of Contents ............................2 Symbols ................................3 Product description ............................3 Centering unit (ST215 and ST215W) ......................3 Connecting the machine ..........................4 Control Elements ............................4 Placing in operation ............................. 5 Setting the centering unit........................5 Setting the Diameter ..........................
The high processing quality paired with high-quality materials make the ST215 a robust production machine. The ST215 is a real all-rounder; it masters stripping of standard cables in short cycle times as well as micro-coaxial cables with highest precision. The absence of grippers allows the ST215 to process shortest cable ends, crushes on the outer jacket are excluded.
Connect the machine with the supplied power supply unit to the mains supply and to the "24V DC" connection. If the power plug is not compatible with your power outlet, please contact your Nitronic partner or contact us directly.
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Placing in operation The sequence of the settings should be observed, since changes to the stripping diameter, due to the design, require adjustments to the stripping length! For adjustments on the stripping head, i.e.
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Setting the Wayback (ST215W only) The Wayback is an opening of the blades before pulling off the jacket. This allows a slightly deeper cut without touching the conductor or shield during the pull-off.
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Setting the rotation duration / incision rate The rotation duration and the incision rate are selected with the same switch. The longer the setting of the rotation duration, the shorter the incision rate.
Page 8
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Adjust machine Insert the cable end to the sensor Without foot pedal With foot pedal When the cable touches the Start the stripping cycle with...
Maintenance is limited to cleaning the stripping head. Lubrication The ST215 is designed so that no grease or oiling is required. In order to ensure good function and a long service life, no greasy or oily substances may get into the device!
Page 10
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Insert the position retainer into the stripping head as shown in Fig. by pushing the large Allen screw at the longitudinal scale to the rear. This makes it easier to insert ...
Loosen screw (19) (black) and turn the centering scale (17) clockwise to diameter 2.0 mm. Retighten screw (19) (black) and remove calibrating pin (30). The ST215 is now ready for use. Dismantling the centering unit Loosen screw (19) (black) and remove centering scale (17) with a slight turning movement Fig. 11.
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Push the two keys (22) out of the guides with a pair of tweezers and remove them Fig. 13. The guide plate (23), the centering jaws (25) and the helixes (26) can now be removed together Fig. 14.
Page 13
Nitronic AG Mattenstrasse 11 Sdasdasdsdfdsdcdscsdcdcd 2555 Bruegg Email: info@nitronic.ch cdcsc Switzerland Phone: +41 32 373 70 70 Screw on nut (18) and tighten up Fig. 17. Fig. 17 Fig. 18 Insert the two keys (22) and install the previously-greased O-ring (20) Fig.
Then by rotating the centering scale (17) close the centering jaws as far as the calibrating pin (30) Fig. Loosen screw (19) (black) and turn the centering scale (17) clockwise to diameter 2.0 mm. Retighten carefully screw (19) (black) and remove calibrating pin (30). The ST215 is now ready for use.
Weight 850g Stripping blades 4 pcs. Carbide, Titanium coated Power supply (Primary) 100-230 VAC, < 0.6A RMS, 47-63 Hz Power supply ST215 (Secondary) 24 VDC Compressed air 5 to max.8 Bar Outer hose diameter 6mm (0.24“) We reserve the right to make technical changes at any time!